Jensen Complete Guide to Installing Your Car Stereo System: JMD200

Page 5

JMD200

INSTALLATION

Before You Begin

1.Disconnect Battery

Before you begin, always disconnect the battery negative terminal.

2.Remove Transport Screws

Important Notes

Before final installation, test the wiring connections to make sure the unit is connected properly and the system works.

Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

Consult with your nearest dealer if installation requires the drilling of holes or other modifications to your vehicle.

Install the unit where it does not interfere with driving and cannot injure passengers if there is a sudden or emergency stop.

If the installation angle exceeds 30º from horizontal, the unit may not give optimum performance.

Avoid installing the unit where it will be subject to high temperatures from direct sunlight, hot air, or from a heater, or where it would be subject to excessive dust, dirt or vibration.

DIN Radio Installation

This unit is designed for installation in vehicle cabs with an existing 1-DIN radio opening. In many cases, a special installation kit will be required to mount the radio to the dashboard. These kits are available at electronics supply stores and car stereo specialty shops. Always check the kit application before purchasing to make sure the kit works with your vehicle.

to a secure part of the dashboard, either above or below the radio using the screw and flange nut provided. Bend the strap to position it as necessary.

CAUTION: The rear of the radio must be supported with either the perforated strap or the rubber mounting bushing to prevent damage to the dashboard from the weight of the radio or improper operation due to vibration.

PERFORATED SUPPORT STRAP

SECURE THIS END TO

REAR OF RADIO

DIN MOUNTING SLEEVE

LOCKING TABS

REAR SUPPORT SCREW

SECURE THIS END TO

SUB-DASH STRUCTURE

REMOVAL KEYS

MOUNTING SURFACE OPENING

NOTE: IF OPENING DOES NOT EXIST,

USE MOUNTING SLEEVE AS A TEMPLATE

AND CUT OPENING. FILE EDGES TO FIT

IF NECESSARY. DO NOT OVER FILE.

Universal Installation (Using Mounting Sleeve)

1.Slide the mounting sleeve off of the chassis. If it is locked into position, use the removal keys (supplied) to disengage it.

2.Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve slides easily into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis. Connect wires prior to actually installing the sleeve. Pigtail wiring should take place after hole size is confirmed. Mount sleeve after wiring.

3.Follow the wiring diagram carefully and make certain all connections of the wiring harness are properly secured and insulated to insure proper operation of this unit. After completing the wiring connections, turn the unit on to confirm operation (ignition switch must be “on”). If unit does not operate, recheck all wiring until the problem is corrected. Once proper operation is achieved, turn off ignition switch and proceed with final mounting of the chassis.

4.Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve fully inserted into the dash opening, bend tabs outward so that the sleeve is firmly secured to the dashboard.

5.Carefully slide the radio into the mounting sleeve making sure it is right side up until it is fully seated and the spring clips lock it into place.

6.Attach one end of the perforated mounting strap (supplied) to the screw stud on the rear of the chassis using the flange nut provided. Fasten the other end of the perforated strap

Kit Installation

1.If your radio requires the use of an installation kit to mount this radio, follow the instruc- tions included in the kit to attach the radio to the mounting plate supplied with the kit.

2.Wire and test the radio as described.

3.Install the radio/mounting plate assembly to the sub-dash according to the instructions of the installation kit.

4.Attach the support strap to the radio and dashboard as described above.

5.Replace the dashboard trim panel.

 

MOUNTING TAB DETAILS

 

CUTAW AY VIEW OF

TOP TAB BEND

SIDE VIEW

MOUNTING SURFACE

 

UPW ARD 90°

MOUNTING

 

 

 

MOUNTING

SURFACE

 

 

 

SLEEVE

 

BEND TABS

BOTTOM TAB

BEND DOWNW ARD 90°

3

Image 5
Contents JMD200 Contents System Features Disc Maintenance Safety InformationInstallation Wiring Diagram Removing the Unit Reconnecting the BatteryBasic Operation Displaying the Clock Setting the ClockTime/Frequency Display Selector T/F Tuner Operation Controlling Disc Playback CD Player OperationInserting and Ejecting a Disc Interference Care and Maintenance TroubleshootingIgnition General SpecificationsFM Radio ASA Electronics Corporation 080207