Jensen JHD1510 System Menu, Equalizer, Loudness, Auxiliary Input, PA Operation, Setting the Clock

JHD1510

System Menu

1.Press and hold the AUDIO/MENU button (3) for more than 2 seconds to enter the system menu. The first menu item, “Beep Tone”, will appear on the display.

2.Press the AUDIO/MENU button repeatedly to navigate the system menu and select the desired item.

3.Use the rotary encoder (1) to adjust the selected menu item.

The following items can be adjusted:

•Beep Tone (ON/OFF): Turn the audible beep ON/OFF (heard when functions/buttons are selected).

•Region (USA/EURO): Set frequency spacing for various regions.

•Time Zone: Set the local time zone (used only for Sirius satellite mode).

•DST (Observed/Not Observed): Set for Daylight Savings Time (used only for Sirius satellite mode).

•Clock (12Hr/24Hr): Select 12 or 24 hour display mode.

•Brightness (Low/Mid/High): Adjust LCD brightness.

•Contrast (Low/Mid/High): Adjust LCD contrast.

•Color (Amber/Green): Adjust for desired panel backlight color.

•Pwr On Vol (0 – 40): Select an automatic turn-on volume.

•iPod Auto (ON/OFF): Choose ”ON” to automatically detect and playback iPod when connected or “OFF” to use the MODE button to select the iPod source.

•TA Volume (0-40): Adjust for desired Traffic Announcement volume level.

•WB Alert (ON/OFF): Choose “ON” to switch to Weatherband mode when NOAA weather alerts are issued. (See “NOAA Weather Alert” on page 8.)

•Alert PWR (AUTO/OFF): Select “Auto” to turn on the radio when NOAA alerts are issued. This function only works when the +12V switched is on.

•Default Set (NO/YES): Choose “YES” to return the EEPROM to factory default set up values.

Equalizer

Press the EQ/LOUD button (11) to choose one of the following pre-defined bass and treble curves: OFF > FLAT > ROCK > POP > CLAS(SIC).

Loudness

Press and hold the EQ/LOUD button (11) to toggle loudness on/off. When listening to music at low volumes, this feature will boost the bass and treble ranges to compensate for the characteristics of human hearing.

Auxiliary Input

To access an auxiliary device:

1.Connect the portable audio player to either the AUX IN on the front panel (17) or at the rear of the unit.

2.Press the MODE button (4) to select “AUX” mode. The rear AUX audio source will play by default until a device is inserted into the front jack.

3.Press MODE again to cancel “AUX” mode and go to the next mode.

PA Operation

•Connect the PA Microphone with a 4-PIN connector to the 4-PIN socket on the rear of the unit.

•The unit will automatically switch to PA mode when the Mic switch is pushed “ON”.

•The PA output level can be adjusted using the rotary volume encoder (1).

•With radio power off, the radio will wake up when PA mic is keyed to make an announcement. Radio will return to off state when PA mic is released.

Liquid Crystal Display (LCD)

The current frequency and activated functions are shown on the LCD panel (20).

NOTE: LCD panels may take longer to respond when subjected to cold temperatures for an extended period of time. In addition, the visibility of the characters on the LCD may decrease slightly. The LCD display will return to normal when the temperature increases to a normal range.

Setting the Clock

To set the clock to display the current time, turn the vehicle ignition on and turn the radio off. Press and hold the DISP/SCROLL button (12) for more than one second and the time will flash in the display. Press the TUNE/SEEK << button (18) to adjust the hours or the TUNE/SEEK >> button (19) to adjust the minutes. When in 12Hr Clock mode, “AM” or “PM” will appear on the display to indicate AM or PM. When no adjustment is made for five seconds, the time will become set and normal operation will resume.

Scroll

When the information is too long to be displayed on the LCD, press and hold the DISP/ SCROLL button (12) to view the entire title. The information will scroll twice and then return to abbreviated text.

NOTE: The front AUX IN jack will override the rear auxiliary audio inputs.

6