Insignia CQ-EH8160AK dimensions Terminals Description, Main Block

HONDA / CQ-EH8160AK

8 TERMINALS DESCRIPTION

8.1.Main Block

IC601 : C2CBHG000077

Pin	Port	Description	I/O	(V)
No.
1	BEEP	Beep output	O	0
2	IDC-ST/SP	CD.C start/stop	O	4.9
3	EVOL CLK	Electronic volume clock	O	0
4	EVOL DATA	Electronic volume data	O	0
5	SEC-LED	Security LED on/off	O	4.9
6	VOL A	Rotary encoder data	I	0.5
7	VOL B	Rotary encoder data	I	0.5
8	LCD-CLK	Shift clock for LCD data	O	0
9	LCD-DI	LCD data	O	5.0
10	LCD-DO	LCD data	I	0
11	RESET	Reset input	I	4.9
12	XT2	Crystal oscillator terminal	-	2.4
13	XT1	Crystal oscillator terminal	-	0.7
14	VSS	Ground	-	0
15	X2	Crystal oscillator terminal	-	2.3
16	X1	Crystal oscillator terminal	-	1.8
17	REGOFF	(Connecting to VDD)	-	4.9
18	REGC	(Connecting to VDD)	-	4.9
19	VDD	+5V power supply	-	4.9
20	VOL C	Rotary encoder data	I	4.8
21	VOL D	Rotary encoder data	I	0.5
22	LCD-CE	LCD driver enable	O	0
23	BOSE	(Connecting to ground)	-	0
24	SEC-CS	Security ROM chip select	O	0
25	SEC-CLK	Data shift clock for security ROM	O	0
26	SEC-DI	Security data	I	0
27	SEC-DO	Security data	O	0
28	SET-SEC1	(Ground pull-down)	-	0
29	SET-TIME2	(Vdd pull-up)	-	4.9
30	SET-TIME	(Vdd pull-up)	-	4.9
31	P.CONT	COM8V power switch	O	4.8
32	ACC CNT	ACC 5V power switch	O	4.9
33	STB	Power amp. Stand-by	O	4.9
34	LCD ON	LCD illumi. on/off	O	4.9
35	TUNER +B	Motor antenna power	O	4.9
36	PLL-CE	PLL chip select	O	0
37	PLL-DO	PLL data	O	0
38	PLL-CLK	Shift clock for PLL data	O	0
39	PLL-DI	PLL data	I	5.0
40	VSS	Ground	-	0
41	VDD	+5V power supply	-	4.9
42	AREA	(Ground pull-down)	-	0
43	ST-IND	FM stereo detection	I	0.3
44	CA.PON	Tape power control	O	4.9
45	CM.PON	Tape power control	O	4.9
46	M2	Main motor control	O	0
47	M1A	Loading motor control	O	0
48	M1B	Loading motor control	O	0
49	T.IN	Tape-in detection	I	0
50	MSM	MS gain contrl	O	4.9
51	A/B	Tape side detection	I	0
52	M2F	Main motor control	O	0
53	EQ(MTL)	Metal tape mode selection	O	4.9
54	F/R	Tape head change	O	0
55	DOLBY	Dolby NR on/off	O	4.9
56	T.LOAD	Tape loading detection	I	0
57	MS(PL/FF)	MS mode selection	O	0
58	MS	MS detection	I	0
59	REMO3/4	(Ground pull-down)	-	0
60	H.BUSOUT	Not used	-	-

61	NAVI-IN	(Vdd pull-up)	-	4.8
62	NC	No connection	-	-
63	NC	No connection	-	-
64	NAVI-MUTE	Not used	-	-
65	BIT1	Tape mode switch	I	4.6
66	END.A	Tape end signal	I	1.5
67	END.B	Tape end signal	I	2.4
68	BIT2	Tape mode switch	I	4.6
69	EQ	Metal/Normal switchl	I	0
70	BIT3	Tape mode switch	I	0
71	NC	No connection	-	-
72	NC	No connection	-	-
73	IC/VPP	(Connecting to ground)	-	0
74	REMO	Remote control signal	O	5.0
75	SW.A	Audio signal switch	O	0
76	SW.B	Audio signal switch	O	0
77	MUTE	Not used	-	-
78	NC	No connection	-	-
79	NC	No connection	-	-
80	VSM	Phase diff. level detection	I	0.6
81	AMP MUTE	Power amp mute	O	0
82	AVDD	+5V power supply	-	4.9
83	AVREF1	Analog reference voltage	I	5.0
84	AVSS	Ground	-	0
85	NC	(Connecting to ground)	-	0
86	NC	No connection	-	-
87	ACC-DET	ACC level detection	I	4.5
88	TAPE EJ	Tape eject SW	I	4.6
89	H.BUS.IN	Not used	-	4.8
90	GAIN	(+5V pull-up)	-	4.8
91	IDCEJECT	CD disc eject SW	I	4.7
92	BAT-DET	Battery level detection	I	4.5
93	EJ.INH	Tape/Disc eject SW	I	4.4
94	IDC-SI	CD.C serial data	O	4.0
95	RXO	Not used	-	0
96	TXO	Not used	-	4.9
97	IDC-CLK	Shift clock for CD.C data	O	4.9
98	IDC-SO	CD.C data	O	1.2
99	CD-RESET	CD.C reset	O	4.9
100	CDON	CD.C controller enable	O	4.9

Note :

Voltage measuerments are with respect to ground, with a voltmeter (Internal resistance : 10M ohms.)

8.2.Display Block

IC901 : YEAMLC75853

Pin	Port	Description	I/O	(V)
No.
1, 2	S1, 2	Disc LED on/off	O	0
3	S3	Not used	-	-
4-40	S4-40	LCD segment data	O	2.5
41-43	COM1-3	LCD common	O	2.5
44	S41	LCD segment data	O	2.5
45-49	KS2-6	Key strobe	O	0.9
50-53	KI1-4	Key data	I	0
54	KI5	(Connecting to ground)	-	0
55	TEST	(Connecting to ground)	-	0
56	VDD	+5V power supply	-	5.1
57	VDD1	LCD angle	-	3.3
58	VDD2	LCD angle	-	1.7
59	VSS	Ground	-	0
60	OSC	Oscillator terminal	-	3.9

7