Kicker Complete Guide to ZX Series Amplifiers: ZX150.2 and ZX200.2
Page 2

 

 

 

ZX.2SeriesAmplifier

 

 

 

Owner’sManual

TwoChannelModels:

ZX150.2 / ZX200.2 / ZX250.2

 

Authorized Kicker Dealer:

__________________________

Congratulations on your

 

 

 

KICKER purchase!

Purchase Date:

 

__________________________

Please record your purchase

Amplifier Model Number:

__________________________

information and keep your sales

 

 

 

receipt for validation of warranty.

Amplifier Serial Number:

__________________________

 

Installation

1.Mounting Choose a structurally sound location to mount your Kicker amplifier. Make sure there are no items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier.

2.Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint and corrosion free solid metal area of the vehicle's chassis. Adding an additional ground wire of this same gauge (or larger) between the battery's negative post and the vehicle chassis is recommended.

The ZX amplifier has dual input sensitivity differential RCA inputs which will receive either high or low level signals from your car stereo’s source unit. Ideally, when connecting the source unit to the amplifier, the ZX amplifier’s input level switch should be set to “LO” and a low-level signal should run from the source unit’s stereo RCA output to the stereo RCA input on the end panel of the amplifier using RCA

Figure 3

Bridged Operation (Mono)

Minimum impedance of 4 ohms while in bridged operation

(60cm)

24"

Ground

Remote

Turn-On

(45cm)

18"

+12V Fuse

Battery

Figure 4

Stereo and Mono Operation Simultaneously (SAMS)

Minimum impedance of 4 ohms mono and 2 ohms per channel in stereo simultaneously

(60cm)

24"

Ground

Remote

Turn-On

(45cm)

18"

+12V Fuse

Battery

Bridge Wiring

Signal Out

Signal In

 

 

 

 

 

Low Pass

 

 

 

 

 

XOVER

 

High Pass

 

 

 

 

 

 

 

XOVER

_

_

+

 

 

 

 

Signal Out

 

 

 

 

 

Signal In

 

 

Bridge Wiring

 

 

 

 

 

 

 

High Pass

_

+

 

 

 

XOVER

 

 

 

 

+

 

 

 

 

CONFIGURATION

interconnect cable. If a low-level stereo RCA output is not available on the source unit, the signal can be delivered to the amplifier using the high-level speaker outputs on the source unit. Set the input level switch on the end panel of the amplifier to “HI”. Crimp and solder RCA connectors to the end of the speaker wire running from the high-level speaker outputs on the source unit and connect the wire to the RCA Inputs on the end panel of the amplifier as shown in Figure 1. Either input method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to another amplifier or component. Keep the audio

 

signal cable away from factory wiring

High-level Speaker Output Wire

+

+ Core Cable

 

Figure 1

 

> To Source Unit

 

 

 

+

INSTALLATION

harnesses and other power wiring. If

 

 

 

 

 

 

 

>

you need to cross this wiring, cross it

 

 

Ground or Shielding

To Amplifier

 

 

 

at a 90 degree angle.

Install a fuse within 18” (45cm) of the battery and in-line with the 8 gauge power cable connected to your amplifier. If you ever need to remove the amplifier from the vehicle after it has been installed, the ground wire should be the last wire disconnected from the amplifier--just the opposite as when you installed it. See the fuse chart on the following page for power and ground wire size, and fusing recommendations.

3.Configuration The following diagrams show the most common configurations for your Kicker ZX series amplifier.

Figure 2

Two Channel Operation (Stereo)

Minimum Impedance of 2 ohms per channel in stereo operation

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(60cm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

24"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Signal Out

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ground

 

 

 

 

 

Remote

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Signal In

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Turn-On

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(45cm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

18"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+12V

 

 

 

Fuse

 

 

 

 

 

Battery

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ModelZX150.2

1 (ONE) 25 AMPERE FUSE

PowerGroundWire 8GA

ModelZX200.2

1 (ONE) 30 AMPERE FUSE

PowerGroundWire 8GA

ModelZX250.2

1 (ONE) 40 AMPERE FUSE

PowerGroundWire 8GA

Performance

 

 

 

 

Model

 

ZX150.2

ZX200.2

ZX250.2

 

 

 

 

RMS Power in Watts, all channels driven

60 x 2

70 x 2

85 x 2

@14.4 Volts, 4Ω stereo, ≤ 1% THD+N

 

 

 

 

 

 

 

 

@ 2Ω stereo, ≤ 1% THD+N

 

75 x 2

100 x 2

125 x 2

 

 

 

 

 

@ 4Ω mono, ≤ 1% THD+N

 

150

200

250

 

 

 

 

 

Length: in(cm)

 

10 1/4 (26)

10 1/4 (26)

13 1/2 (34.2)

 

 

 

 

Specifications common to all models:

 

 

 

 

 

 

 

 

Height: in(mm)

 

 

2 1/8 (54mm)

 

 

 

 

 

 

Width: in(mm)

 

 

9 5/8 (244mm)

 

 

 

 

 

 

Frequency Response, ± 1 db:

 

 

20 Hz - 20 kHz

 

 

 

 

Signal-to-Noise Ratio:

 

>95db, a-weighted, re: rated power

 

 

 

 

Input Sensitivity:

 

Low Level: 125mV-5V

 

 

High Level: 250mV-10V

 

 

 

 

 

 

 

Selectable Electronic Crossover:

 

HI, LO or OFF (bypass), Variable 50 - 200Hz, 12db/Octave

 

 

 

Bass Boost:

 

Variable 0-18db Bass Boost @ 40Hz

2

ZX.2AMPLIFIER

Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.

3

 

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Stereo Amplifier Kicker purchase InstallationCongratulations on your PerformanceOperation TroubleShootingImproves, the speaker was out of phase Protection circuitryElectronicsLimitedWarranty InternationalWarranty
Related manuals
Manual 4 pages 52.34 Kb Manual 28 pages 55.38 Kb Manual 28 pages 43.67 Kb

ZX250.2, ZX150.2, ZX200.2 specifications

The Kicker ZX series of amplifiers, including the ZX200.2, ZX150.2, and ZX250.2, represents a significant leap in performance and reliability for car audio enthusiasts. These amplifiers are designed to provide powerful sound and enhanced audio clarity, making them an ideal choice for anyone looking to upgrade their vehicle’s sound system.

The Kicker ZX200.2 amplifier delivers 200 watts of power at 2 ohms, making it ample for both driving full-range speakers and powering subwoofers. One of its standout features is the built-in crossover, which allows users to tailor their sound by adjusting the high-pass or low-pass filters. The ZX200.2 also operates efficiently, with a compact design that simplifies installation without compromising on power.

On the other hand, the ZX150.2, with its 150 watts of power, is perfect for those looking for a robust yet space-efficient amplifier. It includes a variable high-pass filter as well, which ensures precision sound delivery. This model emphasizes Kicker’s commitment to producing amplifiers that produce high-quality sound while remaining affordable and user-friendly. The ZX150.2's low-profile chassis allows it to fit easily into tighter spaces, making it a popular choice for those with limited installation options.

For those needing more power, the ZX250.2 elevates performance with 250 watts of power output. This amplifier excels in driving large speakers and low-frequency components without distortion. Featuring advanced heat management technologies, the ZX250.2 is designed for long-term usage without the risk of overheating. It also includes adjustable bass boost, allowing audiophiles to enhance low-frequency performance to their liking.

All models in the ZX series incorporate Kicker’s Legendary sound quality technology, characterized by low distortion and high dynamic range. They are built with high-grade components and are engineered for flexibility, accommodating various system configurations. Additionally, their sleek design and durable construction ensure that they can withstand the rigors of everyday driving.

In conclusion, the Kicker ZX200.2, ZX150.2, and ZX250.2 amplifiers exemplify the perfect blend of power, quality, and user-adjustability. Whether you’re a casual listener or an audio aficionado, these amplifiers provide the performance and reliability necessary to take your car audio experience to the next level. With their advanced features and robust designs, Kicker amplifiers are an investment in superior sound quality for any vehicle.
Top Page Image Contents