![](/images/new-backgrounds/1221217/2212177x1.webp)
Q4.80 / Q4.150 / Q1.1500D
Features
Q4.80
Q4.150 | CLIP INDICATOR | CLIP INDICATOR | |||
| HARD CLIP |
| HARD CLIP | ||
|
| AMBER- |
|
| AMBER- |
| GREEN- | SOFT CLIP | GREEN- | SOFT CLIP | |
| PRE CLIP | RED- | PRE CLIP |
| RED- |
| LEVEL | LEVEL | |||
| 9V | 0.2V | 9V |
| 0.2V |
| BASS BOOST | BASS BOOST | |||
| 0dB | 12dB | 0dB |
| 12dB |
| MULTIPLIER | BASS FREQUENCY | |||
|
|
|
| ||
| FREQUENCY |
|
|
| |
|
|
| 30Hz |
| 80Hz |
| X15 | X1 | HIGH PASS | ||
| FILTER SLOPE |
|
|
| |
| 6dB | 12dB | 15Hz |
| 1KHz |
| CHANNELS 1&2 | CHANNELS 3&4 | |||
| HIGH PASS | LOW PASS | |||
| (x1) 20Hz | 300Hz | 40Hz |
| 4.5KHz |
| (x15) 300Hz | 4.5KHz | CROSSOVER | ||
| CROSSOVER | ||||
|
|
|
| ||
| DUPE | ||||
| MONO STEREO | ||||
| (3&4) |
| |||
| PROTECT | INPUT MODE | |||
|
|
|
| ||
| POWER | 4CH | 2CH | ||
|
|
|
-CLIP INDICATOR:
-GREEN =
-AMBER = Soft Clip
-RED = Hard Clip
-LEVEL: Variable sensitivity from 0.2V to 9V
-BASS BOOST: Variable bass boost from 0dB to 12dB
-BASS FREQUENCY: Frequency to be boosted, variable from 30Hz to 80Hz
-HIGH PASS:
-CH3&4: Variable HIGH PASS filter from 15Hz to 1KHz
-CH1&2: Variable HIGH PASS filter from 20Hz to 300Hz
-MULTIPLIER FREQUENCY: Available for CH1&2 only and variable selector for x15 or x1 the selected HIGH PASS value
-FILTER SLOPE: Roll off for HIGH PASS on CH1&2, selectable at 6dB or 12dB
-CROSSOVER:
-CH3&4:
-
-
-
-CH1&2:
-DUPE (3&4): Bypasses all variables on CH1&2 and duplicates settings from CH3&4
-
-PROTECT: Red LED which indicates PROTECTION
-POWER: Green LED which indicates the amplifier is “ON”
-INPUT MODE:
-4CH: Selected when two sets of RCA’s are being connected to CH1&2 and CH3&4
-2CH: Selected when only one set of RCA’s are being connected to CH1&2. The amp will automatically provide signal to CH3&4 but there will be no FADE from front to rear on your headunit controls.
Q1.1500D
|
|
| ||
| PROTECT | |||
| ||||
| POWER |
|
|
|
|
|
| CLIP INDICATOR | |
LEVEL | CONTROL |
| ||
|
|
| ||
|
|
| ||
9V | 0.2V |
| INPUT | OUTPUT |
| SLAVE | MASTER | ||
|
|
| ||
PHASE SHIFT |
| SUBSONIC | ||
0 | 180 |
| 15Hz | 35Hz |
PARAMETRIC BASS EQ | ||||
BASS BOOST | LOW PASS | |||
0dB | 12dB | 35Hz | 200Hz | |
BANDWIDTH | BASS FREQUENCY | |||
|
|
| 30Hz | 80Hz |
WIDE | NARROW |
|
|
-PROTECT: Red LED which indicates PROTECTION
-POWER: Green LED which indicates the amplifier is “ON”
-CLIP INDICATOR:
-GREEN =
-AMBER = Soft Clip
-RED = Hard Clip
-LEVEL: Variable sensitivity from 0.2V to 9V
-
-INPUT SLAVE: Selected when amplifier is being linked as SLAVE and receiving signal from the MASTER amplifier. When in INPUT SLAVE position all other adjustments are bypassed
-OUTPUT MASTER: Selected when amplifier is being linked as MASTER and providing signal to the SLAVE amplifier. This amplifiers’ adjustments now control both amps
-PHASE SHIFT: Adjustable time alignment from 0 to 180 degrees
-SUBSONIC: Variable from 15Hz to 35Hz
-LOW PASS: Variable from 35Hz to 200Hz
-BASS BOOST: Variable bass boost from 0dB to 12dB
-BASS FREQUENCY: Frequency to be boosted, variable from 30Hz to 80Hz
-BANDWIDTH: Range of frequencies to be boosted
-Variable from WIDE to NARROW. WIDE includes less frequencies to be boosted while NARROW includes more frequencies to be boosted above and below the selected frequency
3