Single AMP Installation Procedure, Not Used

BRZ2100.1D / BRZ2400.1D / BRZ3000.1D PRO MONO AMPLIFIER APPLICATIONS

Basic application

SINGLE AMP INSTALLATION PROCEDURE:

1.Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out puts with good quality RCA interconnect cables.

2.Plug in the HFR-3 remote module into the amp REMOTE INPUT jack.

3.Route a 0 gauge power cables directly to the vehicle battery with an in-line fuse.

4.Connect a 0 gauge ground cables directly to chassis ground with in 36” of the amp.

-Be sure to remove any paint or primer from the ground point.

-Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.

5.Connect the subwoofer(s) in accordance to the diagrams below.

6.Make sure the MASTER/SLAVE switch is in the MASTER position.

Note: The amplifier will not work if the MASTER/SLAVE switch is in the Slave position

FULL RANGE
STEREO LINE INPUT	Y-ADAPTOR

NOT USED

Note: You can use the Radio/CD designated mono line output or a full range stereo line output. For full range stereo line output, you will need an optional “Y-Adaptor” as shown.

DESIGNATED

MONO OUTPUT FROM HEAD UNIT

BOOST

HFR -3 MIN MAXX

	R	L	INPUT
			INPUT
	R	L	OUTPUT	BALANCED
	9V 0.2V		INPUT LEVEL	BALANCED
	0 180		PHASE
	0dB 10dB		REMOTE
	0dB 10dB		BASS EQ
	15Hz 35Hz		SONIC	SUB
	35Hz		LOW
	250Hz		PASS
INPUT SLAVE	OUTPUT MASTER			PROTECT	POWER
OUT			IN

		MONO
		SUBWOOFER
		PARALLEL MONO
	+	SUBWOOFERS
	OUTPUT +	SUBWOOFERS
	OUTPUT +	2 OHMS EACH MINIMUM
	SPEAKER - -
	REM	REMOTE TURN-ON
		POWER	SPEAKER
		+12V GND	REM - - + +
INPUT	GND	CHASSIS GROUND
POWER	BATT+12V	TO BATTERY + 12 Volts
		VIA FUSE

DUAL AMP INSTALLATION PROCEDURE:

1.Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out puts with good quality RCA interconnect cables.

2.Plug in the HFR-3 bass remote module into the amp REMOTE INPUT jack on the Master amp. This will allow the Master amp to control both Master and Slave amps with just one Bass Remote.

3.Connect an RCA jumper cable from the Master amp MASTER OUTPUT to the Slave amp SLAVE INPUT. Note: This will “link” the amps so that the Master amp crossover switches will control both the Master and Slave amps. The Slave amp crossover switches will be bypassed.

4.Route two 0 gauge power cables directly to the vehicle battery with an in-line fuse.

5.Connect two 0 gauge ground cables directly to the chassis with in 36” of the amp.

-Be sure to remove any paint or primer from the ground point.

-Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.

6.Make sure the Master amp MASTER/SLAVE switch is in the MASTER position. Make sure the Slave amp MASTER/SLAVE switch is in the SLAVE position.

7.Connect the subwoofer(s) in accordance to the diagrams below.

8.Connect a 12 gauge jumper from Master amp speaker - to Slave amp speaker - as shown below.

Linking two amps for single or dual subwoofer application

Amplifiers are stable to 2-Ohms linked

	R	L	INPUT
DESIGNATED			INPUT
MONO OUTPUT			OUTPUT
FROM HEAD UNIT	R	L	OUTPUT
FROM HEAD UNIT			BALANCED INPUT LEVEL
	9V 0.2V		BALANCED INPUT LEVEL
BOOST	0 180		PHASE
			REMOTE

		+
	(MASTER)	OUTPUT +
	(MASTER)	SPEAKER - -
		SPEAKER - -
		REM

HFR -3 MIN MAXX				0dB 10dB		BASS EQ
Master remote controls				0dB 10dB		BASS EQ
both amplifiers when				15Hz 35Hz		SONIC	SUB
LINKED				15Hz 35Hz		SONIC	SUB
				35Hz		LOW
				250Hz		PASS
		INPUT SLAVE	OUTPUT MASTER				P OTECT	WER
	MASTER OUTPUT TO SLAVE	OUT				IN
RCA JUMPER CABLE	MASTER OUTPUT TO SLAVE	OUT	RR	9V 0.2V 0 1800dB 10dB 15Hz 35Hz	LL	INPUT OUTPUT INPUT LEVEL PHASE REMOTE BASS EQ SONIC	BALANCEDSUB

OUTPUT

MASTER

INPUT	OUT
SLAVE

(SLAVE)

INPUT	GND
POWER	BATT+12V

	+
OUTPUT	+
SPEAKER	- -
	REM

12 GAUGE JUMPER WIRE

INPUT	INPUT SLAVE	OUTPUT MASTER	35Hz 250Hz	LOW PASSP OTECT	WER
	OUT			IN

	IN	INPUT	GND
OUTPUT		INPUT	GND
OUTPUT	OUT	POWER	BATT+12V
INPUT	OUT	POWER	BATT+12V
MASTER
SLAVE

BRZ3000.1D PRO, BRZ2100.1D, BRZ1700.1D, BRZ1200.1D, BRZ2400.1D specifications

Hifonics has established itself as a formidable player in the world of car audio with its BRZ series amplifiers, specifically designed to deliver exceptional power and performance. Among these models are the BRZ2400.1D, BRZ1200.1D, BRZ1700.1D, BRZ2100.1D, and BRZ3000.1D PRO, each catering to different needs and preferences for audiophiles and casual listeners alike.

The BRZ2400.1D boasts an impressive power output, delivering 2400 watts RMS at 1 ohm. This powerhouse amplifier employs advanced Class D technology, which maximizes power efficiency while minimizing heat production. Its advanced circuit design not only enhances reliability but also ensures that users experience crisp, clear audio across a wide frequency range.

The BRZ1200.1D offers a balanced solution for users needing substantial power without overwhelming their system. With a 1200 watts RMS output at 1 ohm, it maintains high efficiency and performance. The compact design allows easy installation in various vehicles, making it an attractive option for those seeking quality in a smaller package.

For those desiring a middle ground, the BRZ1700.1D delivers 1700 watts RMS at 1 ohm. This model is particularly notable for its innovative features, including a low-pass filter, bass boost, and adjustable input sensitivity, allowing users to customize their listening experience to fit their unique audio preferences.

The BRZ2100.1D further amplifies the performance, providing 2100 watts RMS at 1 ohm. This model includes a subsonic filter that helps to eliminate unwanted low frequencies, ensuring that the bass remains tight and controlled.

Finally, the BRZ3000.1D PRO represents the pinnacle of Hifonics power amplifiers, with an astounding 3000 watts RMS at 1 ohm. This model is ideal for enthusiasts looking to push the limits of their audio systems. Increased capacitance and advanced thermal management allow it to handle high power loads without risk of overheating, making it perfect for high-performance setups.

Each amplifier in the BRZ series features a sophisticated protection circuit to safeguard against short circuits, overheating, and overcurrent, providing peace of mind to users. Moreover, with RCA inputs, wire gauge terminals, and adjustable controls, installation and tuning are hassle-free.

The Hifonics BRZ series amplifiers combine power, efficiency, and flexibility, making them an appealing choice for anyone looking to enhance their car audio experience. These amplifiers represent a complete package for sound enthusiasts, ensuring that every note and beat is heard with depth and clarity.