Hyundai H-CDM8019 instruction manual Installation/Connections, Before installation

Page 5

Installation/Connections

First complete the electrical connections, and then check them for correctness. If you are not confident working with electrical wiring, removing and reinstalling interior panels, carpeting, dashboards or other components of your vehicle, please call your dealer in order to have the unit professionally installed.

Before installation

1.Remove the old unit from the dashboard.

￿￿ Remove the outer trim frame.

￿￿ Insert the keys supplied with the old unit into both sides of the unit as shown in figure below until they click. Pull to remove the old unit from the dashboard. Do not disconnect wires at this time!

2.Mark polarity of the speaker wires.

Marking the polarity of the speaker wires will make it easier to connect the existing speakers to your unit. Consult wiring diagram of existing head unit before disconnecting any wires. If you are not positive of the polarity of the existing wires from the speakers to the head unit, install new wires.

￿￿While the old unit is playing, disconnect the wires from one speaker.

￿￿Take a length of masking tape and fold it around the wire so it forms a flag.

￿￿On the masking tape mark the polarity of the speaker wires (+ and -), as well as left or right, and front or rear.

￿￿Repeat this procedure for all of the speakers.

￿￿Mark the power, ground, and any other wires also.

6

Image 5
Contents Ρукοвοдствο пο эксплуатации CDM8019Table of contents Important safeguards Accessories Before installation Installation/ConnectionsMark polarity of the speaker wires Remove the old unit from the dashboardInstallation method a Installation method B Attaching the control panel Detaching the front panelElectrical connections Speaker Wiring NotesUsing the ISO Connector Back of the front panel Panel controlsFront panel General operations Auxiliary input, RCA output DSP modeAuxiliary Input RCA OutputRadio operations Page CD/MP3 operations MP3 Track search modeElectronic Shock Protection ESP Insert/Eject discsSelecting tracks/Fast Forward/Rewind Multi-session CD readingPlay/Pause disc Scanning tracksID3 tag RepeatRandom playback MP3 Overview Cleaning the cabinet CleaningCleaning discs Handling discsSymptom Cause Solution Troubleshooting guideSpecification Description Important safeguards Mounting the speakers Securing the speakers If unit fails to operate properly Symptom Possible Cause SolutionSpecification Увааемый пοкупатель СοдераниеΜеры предοстοрοнοсти Кοмплект пοставки Устанοвка/Пοдключение Βнимание Примечание Βнимание Примечания Ηοмер Функция ISOЭлементы управления Beep Οснοвные οперацииLoud Aux, RCA DSPДοпοлнительный вхοд AUX Βыхοд RCAVOL, «SEEK 1». VOL, «SEEK 1» 1 «SEEK 2» Οперации с радиοAвтοматическοе сканирοвание и сοхранение FM MP3 Οперации с дисками СD/MP3ESP Пοиск пο начальнοму симвοлу Пοиск трекаПοиск файла ID3 Οбзοр ΜΡ3 CD-R CD-RW Οбращение с дисками Чистка и ухοд Ηеисправнοсть Причина Ρешение Ρукοвοдствο пο устранению неисправнοстейΟбщие Τехнические характеристикиFM радиο MW радиοΟписание Mеры безοпаснοсти Устанοвка акустическοй системы Фиксация акустическοй системы Причины неисправнοсти акустическοй системы 120