Carson SC-411-RD-1014 operating instructions Wail, Yelp, Phsr

SC-411RD-10	Installation and Operating Instructions						Page 7 of 12
				Option Set 1
S1 (CUTOUT Input), S2 (SIRCTRL Input),
S3 (LITCTRL Input) - These inputs are			Press		Lever Switch = OFF		Shows blinking
normally activated by a 12V	input (ON).			0↓		On (Default)	Cutout Input Active +
Press the switch once until it FLASHES to				1↓	S1	Flash	Cutout Input Active -
change to ground activation.	Press the
				2		Off	Cutout Input Off
switch again for OFF to disable.
				0↓		On (Default)	Siren Control Input Active +
S4 (Timed Override) - While In Wail, Yelp or					S2
				1↓		Flash	Siren Control Input Active -
Phaser mode, momentarily pressing the
				2		Off	Siren Control Input Off
Manual push button will override the Wail,
				0↓		On (Default)	Light Control Input Active +
Yelp or Phaser tone. With this option ON					S3
the unit automatically goes back to the				1↓		Flash	Light Control Input Active -
previous tone after 10 seconds.				2		Off	Light Control Input Off
S5 (Sweep/Intersection Function) - While in				0↓	S4	Off (Default)	Timed Override Off
Wail, Yelp, or Phaser mode, momentarily				1		On	Timed Override On
activating the siren control input will change				0↓	S5	Off (Default)	Sweep/Intersection Off
the unit into sweep and intersection mode.
		1				On	Sweep/Intersection On
S6 (Automatic Siren Enable)	The Auto-			0↓	S6	On (Default)	Automatic Siren On
matic Siren feature on the Lever switch				1		Off	Automatic Siren Off
Position 3 may be enabled with this switch.

Press the OUT/DIM button momentarily to move into next section, or OUT/DIM for 3 seconds to save & exit.

						Option Set 2
S1 (Two-Tone Enable) - Two-Tone replaces
					Press			Lever Switch = OFF		Shows blinking
Phaser tone when turned ON.
S2 (Phaser/Two-Tone Disable)				- Phaser			0↓	S1	Off (Default)	Phaser
and Two-Tone are disabled when ON.							1		On	Two-Tone Replace
S3 (Short Manual Enable) -			The Manual				0↓	S2	Off (Default)	Phaser/Two-Tone Enable
							1		On	Phaser/Two-Tone Disable
siren	tone will	normally die	out	and stop
							0↓		Off (Default)	Normal Manual
when	Manual	push-button	is	released.				S3
Turning option ON forces the Manual siren							1		On	Short Manual
tone to stop immediately.							0↓	S4	Off (Default)	Horn Enable
S4 (Horn Disable) - Horn tone is disabled							1		On	Horn Disable
when turned ON.							0↓	S5	Off (Default)	Lever 2 Progressive
S5 (Lever 2 Isolated) - Turn ON for L2							1		On	Lever 2 Isolated
output only in Lever switch position 2.							0↓	S6	Off (Default)	Lever 3 Progressive
S6 (Lever 3 Isolated) - Turn ON for L3							1		On	Lever 3 Isolated
output only in Lever switch position 3.

Press the OUT/DIM button momentarily to move into next section, or OUT/DIM for 3 seconds to save & exit.

		Option Set 3
S1 (Alert Enable) - Turn off to disable Alert
	Press		Lever Switch = OFF		Shows blinking
feature (reminder beep).
S2 (Lever/Siren Video) - VIDEO output is		0↓	S1	On (Default)	Alert Enabled
		1		Off	Alert Disabled
normally on when the Lever switch and/or
Siren is active. Press switch to disable.		0↓	S2	On (Default)	Lever/Siren Video Enabled
(NOTE: this does not control the VIDEO		1		Off	Lever/Siren Video Disabled
Output for S1 - S6. See S1 - S6 Operation)

Press the OUT/DIM button momentarily to move into next section, or OUT/DIM for 3 seconds to save & exit.

Second Tone Control

Press S1, S2, S3 or S4 to select the second speaker tone when in the corresponding Function switch setting.

Rotary	Lever Switch = OFF		Shows	&	blinking
Position	S1	S2	S3		S4
WAIL	2nd = Wail	2nd = Yelp	2nd = Phaser		2nd = Two-Tone
YELP	2nd = Wail	2nd = Yelp	2nd = Phaser		2nd = Two-Tone
PHSR	2nd = Wail	2nd = Yelp	2nd = Phaser		2nd = Two-Tone

Press the OUT/DIM button momentarily to go back to beginning, or OUT/DIM for 3 seconds to save & exit. NOTE: These option setting can be easily transferred to another vehicle. See PROGRAM TRANSFER.

CP5094C 7/30/12