Arcam P35 manual Using your C30 pre-amplifier, Front Panel Controls, Volume Control Settings

Page 6

Using your C30 pre-amplifier

C30 PRE-AMPLIFIER

ENTER

MODE RECORD SELECT

PHONO/AUX CD

TUNER

AV

DVD

VCR

TAPE

TONE

MUTE DISPLAY

PHONES

POWER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FRONT PANEL CONTROLS

This section describes how to operate your amplifier.

If your amplifier has not been installed for you, you should first read the section ‘Installation: C30 pre-amplifier’ on page 5.

POWER bn

Switches the unit on and off.

The power indicator light (directly above the switch) shows the status of the amplifier. A red light means the amplifier is in stand-by mode (press the POWER/STANDBY button on the remote control, or the POWER button on the front panel, to switch between stand-by and powered-up modes).

Remote control receiver 1

The remote control’s infrared receiver is positioned behind the ‘FMJ’ badge. Ensure the receiver is in a clear line of sight from the remote control to allow signals to be received.

MODE 2, UP and DOWN 5

These buttons are intended for use with any future optional modules that may become available for the C30. The UP and DOWN buttons, however, are used with the existing C30 pre-amplifier to move the cursor when customising the ‘Welcome message’ (see page 9).

Control knob 7, SELECT 4 and ENTER 6

The control knob has two functions:

as a volume control, to adjust the output of the headphones and of the pre-amp output (PRE OUT).

when used in conjunction with the SELECT and ENTER buttons, to customise amplifier settings (see page 9).

VOLUME CONTROL SETTINGS

It is important to realise that volume level shown on the display is not an accurate indication of the power delivered to your loudspeakers.The amplifier often delivers its full power long before the volume control reaches its maximum position, particularly when listening to heavily recorded compact discs. However the amplifier also has to be capable of giving full power output from much lower level sources, such as tuners and cassette decks. Using these sources, the volume control setting may be much higher before distortion (audible overload) sets in.

It is possible to compensate for these input level differences by using the ‘Input trims’ menu item. See page 9 for further details on how to do this. Adjusting the input levels of each source individually will help to avoid accidental overload.

Source selectors 8

These buttons select the source connected to the corresponding input. A light above the relevant button indicates which input is currently selected and it will also usually be shown on the display. See page 6 for more information on connecting audio sources to the C30.

TONE 9

Switches the tone circuits on and off, including settings for individual sources. Note that the tone LED does not light unless a tone setting has been made. See page 9 for further information on the tone controls.

MUTE bk Silences all main analogue outputs when selected.

DISPLAY bl This switches the display brightness between Off/ Dim/Bright. This is provided to set the display brightness to a level that is comfortable for you. Switching the display off may give a small improvement in sound quality.

PHONES bm

This 1/4-inch stereo jack plug socket accepts headphones with an impedance rating between 32Ω and 600Ω.

The headphone socket is always active.To avoid possible damage, always disconnect headphones prior to switching the amplifier on or off.

6

Image 6
Contents Vorverstärker C30 Vollverstärker P35 Vollverstärker P1 Safety guidelines Important Safety InstructionsSafety Compliance Using this handbook ContentsPower Amplifier Connection Installation C30 pre-amplifierConnectingto a Power Supply Positioningthe UnitConnectingto Other Equipment Using your C30 pre-amplifier Volume Control SettingsFront Panel Controls Recording Showing the volume level and you are ready to recordThis routes the VCR signal to the Tape output TAPE-TO-TAPE Copying DubbingCustomising Amplifier Settings Setting up your C30 pre-amplifierAdjusting Listening Settings IntroductionUsing the remote control CR-389 Remote ControlInstallation P35 and P1 power amplifiers P35 Power Amplifier Rear PanelP1 Power Amplifier Rear Panel Using Bare Wire Ended Leads Connecting LoudspeakersRemote Switching Using Spade TerminalsUsing your power amplifier Fault IndicationsSP1 and SP2 P35 only Beforeyou Start Bi-wiring and bi-amping loudspeakersBI-WIRINGYOUR Loudspeakers BI-AMPINGYOUR SystemContinual Improvement Policy Technical specificationsPower amplifier input Nominal sensitivity 800mV C30 P35Remote-control codes Service information GuaranteeON-LINE Registration English
Related manuals
Manual 59 pages 54.66 Kb Manual 16 pages 40.16 Kb Manual 52 pages 56.22 Kb

P35 specifications

The Arcam P35 is a high-performance power amplifier that has gained recognition among audiophiles and home theater enthusiasts alike for its exceptional sound quality and robust build. Designed to deliver superior audio performance, the P35 is a testament to Arcam’s commitment to engineering excellence and innovative technology.

One of the standout features of the Arcam P35 is its Class G amplification technology. This unique design offers the efficiency of Class D amplifiers while maintaining the warm, rich sound that Class A amplifiers are known for. By utilizing two sets of output transistors for different power levels, the P35 provides additional power when needed without compromising sound quality at lower volumes. This results in remarkably low distortion levels and an impressive dynamic range, making it suitable for everything from subtle acoustic tracks to explosive movie soundtracks.

The P35 is capable of delivering 120 watts per channel into 8 ohms, and an even more powerful 240 watts per channel into 4 ohms. Such power ensures that it can drive even the most demanding speakers with ease. Moreover, the amplifier features both balanced and unbalanced inputs, providing flexibility for various audio setups. The balanced XLR connections help to minimize noise and signal degradation for a clearer sound, particularly in professional settings.

In terms of build quality, the Arcam P35 boasts a robust chassis that minimizes resonance and vibration. The solid construction not only enhances durability but also contributes to an overall cleaner sound. The component selection is top-notch, utilizing high-quality capacitors and transistors designed to withstand the rigors of constant use while delivering exceptional audio fidelity.

An additional characteristic worth noting is Arcam's emphasis on user-friendly design. The P35 features a straightforward layout, allowing for easy setup and operation. It is also equipped with an LED status indicator that provides visual feedback on the amplifier's operational state.

Overall, the Arcam P35 is a powerful and sophisticated amplifier that excels in delivering an immersive audio experience. With its advanced Class G technology, versatile connectivity options, and exemplary build quality, the P35 stands out as an ideal choice for both stereo and home theater applications. Whether you're a casual listener or a serious audiophile, the Arcam P35 is sure to impress with its musicality and performance. Through meticulous engineering and attention to detail, Arcam has successfully created an amplifier that meets the high expectations of audio enthusiasts around the world.