Pioneer XDV-P90 owner manual Connecting the Units, Installation

Page 66

Installation

Installation

Connecting the Units

Note:

•This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recreational vehicle, truck, or bus, check the battery voltage.

•To avoid shorts in the electrical system, be sure to disconnect the · battery cable before begin- ning installation.

•Refer to each product’s manual for details on connecting the power amp and other units, then make connections correctly.

•Secure the wiring with cable clamps or adhe- sive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.

•Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, hand- brake and seat rails. Do not route wiring in places that get hot, such as near the heater out- let. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short- circuiting to the vehicle body.

•Don’t pass the yellow lead through a hole into the engine compartment to connect to the bat- tery. This will damage the lead insulation and cause a very dangerous short.

•Do not shorten any leads. If you do, the protec- tion circuit may fail to work when it should.

•Never feed power to other equipment by cut- ting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating.

•When replacing fuse, be sure to use only fuse of the rating prescribed on the fuse holder.

•If the RCA pin jack on the unit will not be used, do not remove the caps attached to the end of the connector.

•To prevent incorrect connection, the input side of the IP-BUS or optical cable connector is blue, and the output side is black. Connect the connectors of the same colors correctly.

•If this unit is installed in a vehicle that does not have an ACC (accessory) position on the igni- tion switch, the red lead of the unit should be connected to a terminal coupled with ignition switch ON/OFF operations. If this is not done, the vehicle battery may be drained when you are away from the vehicle for several hours.

 

 

CC

 

 

 

 

 

 

 

 

 

F

A

O

 

 

 

F

O

 

 

 

 

N

 

N

O

F

 

 

 

 

O

F

 

 

 

 

 

 

 

S

 

 

 

S

 

 

 

 

 

 

 

 

 

 

 

 

 

 

T

 

 

 

 

T

 

 

 

 

R

A

 

 

 

R

A

 

 

 

T

 

 

 

T

 

ACC position

No ACC position

•Cords for this product and those for other products may be different colors even if they have the same function. When con- necting this product to another product, refer to the supplied Installation manuals of both products and connect cords that

have the same function.

63

Page 65 Page 67
Image 66
Page 65 Page 67
Contents XDV-P90 To establish a safe level Once you have established a comfortable sound levelDecibel Level Example Precaution 7U.S.AContents Appendix About This Product Before Using This ProductHow to Use This Manual About This ManualWhen Using a Display connected to Rear Video Output To Ensure Safe DrivingWhen using this product with a Pioneer compo Preventing the Battery from Becoming ExhaustedChanging the Mode Switch Setting Select the IP-BUS modeTurn the ignition switch OFF Press the Reset button Resetting the MicroprocessorResetting Condition MemoryKey Finder 0OPEN/CLOSEPrecaution Using the Remote ControllerBattery Replacing the Lithium BatteryFeatures of This Player Discs Compatible with this ProductCompatible with DVD, Video CD and CD Formats What the Marks on DVDs Indicate Disc OperationMark Meaning Disc Organization Video CD and CDMain Features of This Product You can play back DVDs, Video CDs PBC compatibility and CDsCare of Discs and Magazines Loading Discs When Using 8 cm 3 in. DiscsLoading Discs Replace the trayLoading the Magazine Load in the direction indicated by the arrowSlide the Open lever to the right Removing the Magazine Eject buttonSwitch the display image source to this product Switching Power ON/OFFSwitching Power on Press the Power buttonPrecautions concerning the IP-BUS Mode Switching Power OFFWhen using a rear display in the IP-BUS Mode Press the Source button for 1 second on the Head UnitDisc DVD/Video CD/CD Playback Working with the Menu ScreenChapter and Track Advance/Return Skipping to the Next Chapter/TrackReturning to the Previous Chapter/Track Specifying Chapter Specifying Title/Chapter/Track Direct SearchSpecifying Title Specifying TrackDisc Fast Forward/Reverse Fast ForwardFast Reverse Stopping Playback Changing DiscsPress the Disc UP/DOWN buttons Press the Stop 7 buttonPress the PLAY/PAUSE 6 button during playback Still, Frame-by-Frame and Slow Motion PlaybackStill Playback Frame-by-Frame PlaybackSlow Motion Playback 16 Ô 1/8 Ô 1/4 Ô 1/2Changing Audio Language during Playback Multi-Audio Changing Audio Output during PlaybackPress the Subtitle button during play Press the Subtitle button while the subtitle selectionSubtitle selection mark Changing the Viewing Angle during Playback Multi-Angle Press the Display button Calling up Information DisplaysOperating with Information Displays Concerning Information DisplayFor Time Time Search Operating with the Information Display 1 of a DVDFor Titles and Chapters Direct SearchFor Subtitles Selecting Audio, Subtitle and AngleFor Audio For AngleSelecting Repeat Range Switching DiscsOperating with the Information Display 2 of a DVD Move the joystick left/right to select the Disc optionPicture mode option is indicated in blue Selecting the Picture ModeMove the joystick left/right to select Picture mode option Operating with the Information Display 1 of a Video CDFor Tracks Displays Move the joystick up/down to switch to the desired settingSelecting Audio Output Move the joystick left/right to select Audio optionDisc option Operating with the Information Display 2 of a Video CDMove the joystick left/right to select Disc option is indicated in blueMove the joystick left/right to select the Track option Operating with the Information Display 1 of a CDSearching for a Desired Track Press the number buttons to input the desired track numberSetting Random Play Setting Scan PlayOperating with the Information Display 2 of a CD Information DisplaysMove the joystick left/right to select Disc option Press the Next ¢ button Calling up the SET UP MenuChanging Initial Settings Returning to the previous displayMove the joystick up/down to select the Subtitle Lang Setting the Subtitle Subtitle LangSetting Subtitles and Assist Subtitles ON/OFF Assist SubtitlesMove the joystick to select the desired lan- guage Setting the Subtitle LanguageWhen You Select Others You can set the preferred subtitle languageSetting the Audio Language Audio Lang Move the joystick up/down to select the Audio LangMove the joystick to select the desired audio language Setting the Menu Language Menu Lang Setting the Parental Lock ParentalSetting the Code Number and Level Level Parental Lock details Move the joystick left/right to select the desired levelCode number is set, and you can now set the level Parental lock level is setYou can change the set Parental Lock level When Playing DVDs Enabling Parental LockChanging the Level New Parental Lock level is setMove the joystick up/down to select the TV Aspect Setting Aspect Ratio TV AspectTV aspect Setting detail Move the joystick up/down to select the desired TV aspectSelected digital output setting is set Setting for Digital Output Digital OutputDigital output Setting detail Move the joystick up/down to select the Digital OutputSelected audio output setting is set Setting Digital and Analog Audio Output OUT SelectionOutput setting Setting detail Move the joystick up/down to select the OUT SelectionMove the joystick up/down to select the Angle Setting Angle Selection Mark Display AngleAngle settings are indicated on the right of the screen Angle is indicated in blue. For details, seeOthers Switching the Remote Control Operation Mode SwitchFunction Compatibility Charts ModelSwitching the Remote Control Code Selection Switch Press the 5 button press the ∞ button to switch OFF Function Compatibility ChartFunction Mode Switching Operating with the Head UnitPrecaution Switch the display picture source to this unitSwitch the head unit’s source to this unit ITS PlaybackSymptom Cause Remedy TroubleshootingCommon problems \ Request repairsMethods are used Problems during DVD playback MenuProblems during Video CD playback Problems during Multi-Channel AV Master Unit connectionError Message Message error numberIf You Forget Your Code Number Language Code Chart Terms Optical Digital Output Multi-Audio Multilingual DialogMulti-Subtitle Parental LockConnecting the Units InstallationConnecting the Power Cord Connection Diagram When connecting the Multi-Channel AV Master UnitGreen Pin cable Red Installation When connecting the Head Unit Front Video Output Connecting a rear display When Using a Display connected Rear Video Output Transportation of Multi-DVD Player Installation Mode Switch SettingInstalling the DVD Player Unit Mounting HorizontallyMounting Vertically Angle Switching Dial Adjustment Mounting AngleInstalling the Remote Sensor Installation Index AppendixMenu language Audio SpecificationsGeneral PlayerPage Page Pioneer Corporation

XDV-P90 specifications

The Pioneer XDV-P90 is a remarkable digital media player that showcases advanced technology and a suite of features designed for superior audio and video playback. This device has garnered attention for its impeccable performance and user-friendly design, appealing to audio enthusiasts and casual listeners alike.

One of the standout features of the XDV-P90 is its high-resolution audio capability, supporting a wide range of file formats including FLAC, WAV, MP3, and AAC. This versatility allows users to enjoy their favorite music without compromising quality. The player incorporates advanced digital-to-analog converters (DACs) that enhance sound fidelity, delivering crisp highs and deep lows, ensuring a superior listening experience.

The XDV-P90 is equipped with a vibrant LCD display that enhances usability. This display provides an intuitive interface to navigate menus and settings, allowing users to quickly access their music library, adjust sound settings, and customize their audio experience. Additionally, the screen's resolution contributes to a visually engaging interaction with the device.

Wireless connectivity is another hallmark of the XDV-P90. With built-in Bluetooth support, users can effortlessly stream music from their smartphones or other devices, eliminating the clutter of cables. The player also features USB ports for connecting external storage devices, enabling quick access to a large library of media files.

In terms of sound enhancement, the Pioneer XDV-P90 includes a range of audio processing technologies such as a 13-band graphic equalizer and customizable presets. This allows users to tailor their listening experience to match their personal preferences or the acoustics of their environment. Furthermore, the player supports various surround sound formats, making it suitable for home theater applications.

The XDV-P90 also emphasizes durability and design. Its sturdy construction ensures that it can withstand the rigors of everyday use while maintaining an aesthetically pleasing appearance that fits well in both contemporary and classic setups. Compact and stylish, this digital media player easily integrates with other components of a sound system.

In summary, the Pioneer XDV-P90 is a cutting-edge digital media player that combines high-resolution audio playback, advanced connectivity options, and customizable sound settings. Its blend of innovative technology, user-friendly design, and robust features makes it a top choice for anyone looking to elevate their audio experience, whether at home or on the go.
Top Page Image Contents