Pioneer GM-3300T owner manual Installation, Specifications, Using the Speaker Input

Connecting the Unit

ENGLISH

Installation ENGLISH

Specifications ENGLISH

Using the Speaker Input

Connect the car stereo speaker output wires to the amplifier using the supplied speaker input connector.

•Do not connect both the RCA input and the speaker input at the same time.

7Connections when using the speaker input

Car Stereo

Speaker output

White/black:	Gray/black:
Left ≠	Right ≠
White:	Gray:
Left +	Right +

Speaker input connector

To speaker input terminal of this unit.

Connecting the Speaker Wires

The speaker output mode can be two-chan- nel (stereo) or one-channel (mono). Connect the speaker leads to suit the mode according to the figures shown below.

•Do not connect both the RCA input and the speaker input at the same time.

Two-channel mode (stereo)

(Left) Speaker (Right)

One-channel mode (mono)

Speaker (Mono)

CAUTION

• Do not install in:

—Places where it could injure the driver or pas- sengers if the vehicle stops suddenly.

—Places where it may interfere with the driver,

such as on the floor in front of the driver’s seat.

•Make sure that wires are not caught in the sliding mechanism of the seats, resulting in a short-cir- cuit.

•Confirm that no parts are behind the panel when drilling a hole for installation of the amplifier. Protect all cables and important equipment such as fuel lines, brake lines and electrical wiring from damage.

•Install tapping screws in such a way that the screw tip does not touch any wire. This is impor- tant to prevent wires from being cut by vibration of the car, which can result in fire.

•DO NOT allow amplifier to come into contact with liquids due to, for example, the location where the amplifier is installed. Electrical shock could result. Also, amplifier and speaker damage, smoke, and overheating could result from contact with liquids. In addition, the amplifier surface and the surface of any attached speakers could become hot to the touch and minor burns could result.

•To ensure proper installation, use the supplied parts in the manner specified. If any parts other than the supplied ones are used, they may damage internal parts of the amplifier, or they may become loose causing the amplifier to shut down.

•Never replace the fuse with one of greater value or rating than the original fuse. Use of an improp- er fuse could result in overheating and smoke and could cause damage to the product and injury including burns.

CAUTION:

To prevent malfunction and/or injury

•To ensure proper heat dissipation of the amplifier, be sure of the following during installation.

—Allow adequate space above the amplifier for proper ventilation.

—Do not cover the amplifier with a floor mat or carpet.

•DO NOT allow amplifier to come into contact with liquids due to, for example, the location where the amplifier is installed. Electrical shock could result. Also, amplifier and speaker damage, smoke, and overheating could result from contact with liquids. In addition, the amplifier surface and the surface of any attached speakers could become hot to the touch and minor burns could result.

•Do not install the amplifier on unstable places such as the spare tire board.

•The best location for installation differs with the car model and installation location. Secure the amplifier at a sufficiently rigid location.

•Make temporary connections first and check that the amplifier and the system operate properly.

•After installing the amplifier, confirm that the spare tire, jack and tools can be easily removed.

Example of installation on the floor mat or on the chassis

1.Place the amplifier where it is to be

installed. Insert the supplied tapping screws (4 ⋅ 18 mm) into the screw holes. Push on the screws with a screwdriver so they make marks where the installation holes are to be located.

2.Drill 2.5 mm (1/8 inch) diameter holes at the point marked, and install the amplifier, either on the carpet or directly to the chassis.

Tapping-screws (4 ⋅ 18 mm)

Drill a 2.5 mm (1/8 inch)	Floor mat
diameter hole	or chassis

Power source		14.4 V DC (10.8 V to 15.1 V allowable)
Grounding system		Negative type
Current consumption		15.0 A (at continuous power, 4 Ω)
Average current drawn*		4.0 A (4 Ω for two channels)
		7.8 A (4 Ω for one channel)
Fuse		25 A ⋅ 1
Dimensions		300 mm (W) ⋅ 60 mm (H) ⋅ 194 mm (D)
		[12 (W) ⋅ 2-3/8 (H) ⋅ 7-5/8 (D) in.]
Weight	2.4 kg (5.3 lbs.) (Leads for wiring not included)
Maximum power output		120 W ⋅ 2 ( 4 Ω) / 300 W ⋅ 1 ( 4 Ω)
Continuous power output	60 W ⋅ 2 (at 14.4 V, 4 Ω, 20 Hz to 20 kHz 0.08% THD)
	150 W ⋅ 1 (at 14.4 V, 4 Ω, 20 Hz to 20 kHz 0.8% THD)
	75 W ⋅ 2 (at 14.4 V, 2 Ω, 20 Hz to 20 kHz 0.8% THD)
Load impedance		4 Ω (2 Ω to 8 Ω allowable)
		(Bridge connection: 4 Ω to 8 Ω allowable)
Frequency response		10 Hz to 50 kHz (+0 dB, –1 dB)
Signal-to-noise ratio		100 dB (IHF-A network)
Distortion		0.008 % (10 W, 1 kHz)
Separation		70 dB (1 kHz)
Low pass filter		Cut off frequency: 80 Hz
		Cut off slope: –12 dB/oct
Gain control		RCA: 400 mV to 6.5 V
		Speaker: 1.6 V to 26 V
Maximum input level / impedance		RCA: 6.5 V / 22 kΩ
		Speaker: 26 V / 40 kΩ
Power output ........................................................................................ 60 W RMS ⋅ 2 channels
	(4 Ω and	1 % THD+N)
	150 W RMS ⋅ 1 channel
	(4 Ω and	1 % THD+N)
	75 W RMS ⋅ 2 channels
	(2 Ω and	1 % THD+N)
Signal-to-noise ratio	80 dBA (Reference: 1 W into 4 Ω)

Note:

•Specifications and the design are subject to possible modification without notice due to improvements.

*Average current drawn

•The average current drawn is nearly the maximum current drawn by this unit when an audio signal is input. Use this value when working out total current drawn by multiple power amplifiers.