Installation

Install Threaded Inserts

Accessories

2	- #8-32 Inserts	1 - Monitor Bracket
	(KMSI832)	(KMB701)
2	- #8-32 x 1/2"	2 - 1/4-20 Star Nut
	Black Machine Screw	(KSN1420)

(KMSB832.5)

Remove Factory Console

Open the console lid and remove the (2)
screws toward the rear of the console. Fold
down the cup holder on the rear of the console
until it hits the stops. Continue to push down
on the cup holder snapping it past the stops.
Remove the (2) screws inside the cup holder
recess. Unsnap the rear portion of the console
and disconnect wiring. The rear radio controls
(if equipped) will be relocated to the Q-View	Factory Console
console.
The power point can be relocated to the
optional factory mounting location inside the
console storage bin if so desired.(see picture at
right)
NOTE: If installing into truck with console	Optional Power Port Location
mounted air vents follow these instructions.

Remove the remaining five screws around the top edge of the console storage bin. Remove the four 10mm bolts in the bottom of the storage bin. Gently lift up and remove the bin. Pull out and remove the Y-shaped portion of the AC ductwork. Block off the ductwork near the front of the console and replace the console storage bin.

Prepare Video Console

Radio Control Unit Re-Installation:

Fit the previously removed rear radio control box into the video console. If the vehicle was not equipped with rear radio controls, fit the supplied color-matched filler plate into the recessed area and secure with the (2) supplied

#8 x 1/2” sheet metal screws through the predrilled holes into the plastic housing.

Wiring and Connections

Route all wires and cables at this time. Install wiring and cables according to the instruction provided with electronic equipment. Run all cable for external video sources at this time.

Installation of Video Console

Prepare the monitor for installation by sliding the small studded bracket into the back panel of the monitor. Run the monitor data cable through the rectangular-shaped hole in the video console and connect to the monitor. Slide the monitor into the console and secure using the (2) supplied star nuts. (Do not overtighten)

Slide the metal bracket on the video console into place between the storage bin and the console and snap into place(Make sure that no cables are pinched). Make a mark on the console using the pre-drilled hole on each side towards the bottom of the video console as a guide. Remove the video console and install one of the supplied metal

inserts into the oblong hole on each side of the console, at the mark previously made.)

Re-connect the factory harness to the rear radio control unit. Re-install the video console and secure with (2) supplied #8-32 x 1/2” machine-thread screws through the pre-drilled holes in the plastic housing into the threaded inserts (Do not overtighten). Replace the two factory screws under the console lid towards the rear of the console.

Final Steps

Re-install all previously removed factory components and panels.

Turn on and test everything.

(If system does not work properly, recheck all connections and fuses).

The installation of your new Video

System is now complete.

Rev 10-01-01

SK-SYTL1 Installed

SK-SYTL1 specifications

The Kenwood SK-SYTL1 is an innovative sound system designed to elevate the audio experience in any setting. Known for its stylish design and impressive audio capabilities, this model caters to both casual listeners and serious audiophiles alike.

One of the most notable features of the Kenwood SK-SYTL1 is its robust connectivity options. It supports Bluetooth technology, allowing users to wirelessly stream music from smartphones, tablets, and other devices. This seamless connectivity makes it easy to enjoy music, podcasts, and audiobooks without the hassle of tangled cables. Additionally, the device is equipped with Wi-Fi capabilities, enabling users to connect to streaming services directly, providing access to a vast library of music.

The SK-SYTL1 is designed with a powerful speaker system that includes a high-performance woofer and tweeter configuration. This setup delivers crystal-clear sound across a wide frequency range, ensuring that both bass-heavy tracks and delicate vocals are represented accurately. The sound quality is further enhanced by built-in digital signal processing, which optimizes the audio output for various genres and listening environments.

Another standout feature is the device's multi-room capability. With the Kenwood SK-SYTL1, users can connect multiple speakers throughout their home, allowing for synchronized playback or the option to play different music in different rooms. This versatility offers an immersive audio experience, perfect for gatherings or simply enjoying music throughout the day.

Furthermore, the system boasts advanced compatibility with voice assistants such as Google Assistant and Amazon Alexa. This integration allows users to control playback, adjust volume, and manage playlists using simple voice commands, adding a layer of convenience and modern functionality.

The design of the Kenwood SK-SYTL1 reflects a contemporary aesthetic, featuring a sleek and minimalist look that fits seamlessly into various interior styles. The user-friendly interface, complete with intuitive controls and a clear display, ensures that navigating through options and settings is straightforward.

In summary, the Kenwood SK-SYTL1 is a versatile and high-quality sound system that combines modern technology with user-friendly features. Its Bluetooth and Wi-Fi support, exceptional sound performance, multi-room functionality, and smart assistant integration make it an excellent choice for anyone looking to enhance their audio experience at home or in social settings. Whether hosting a party or enjoying a quiet evening with music, the SK-SYTL1 stands out as a compelling audio solution.