Installation
Accessories
4 | - | 1 | - Monitor Bracket | |||
|
|
| (KMB701) | |||
2 | - #8 x 1/2" (KMSB832.5) | 2 | - | |||
| Black Machine Screw |
| (KSN1420) |
|
| |
|
|
| ||||
2 | - #8 x 1" (KMSB8321) | 2 | - 5/16" Nylon Spacer |
|
|
|
| (KNS8516) |
|
| |||
|
| |||||
| Black Machine Screw | 2 - Air Controls Bracket | ||||
|
|
| (KMBFAC1) | |||
8 | - #8 x 1/2" BlackSMS | 2 - Mounting Bracket (pr.) (KMBEXNL2) | ||||
|
|
|
|
| ||
(KSMSB8.5)
4 - #6 x 1/4Ó Zinc SMS
(KSMSZ6.25)
Remove Factory Console
Notice that the brackets are drilled universally and will have two unused holes when mounted. Mount the rear air controls to the video console with two of the supplied #8x1/2” sheet metal screws, through the holes in the video console and into the metal brackets.
The color matched filler plate is used in the event the console was not equipped with rear air controls. Install the filler plate from the inside and secure with the (2) supplied #8 x 1/2” sheet metal screws.
To reinstall the rear radio control unit enlarge the four holes in the mounting tabs to 3/16”. Install the four supplied metal inserts into the mounting tabs. Install the radio control unit into the video console with the (2) supplied 1/2” machine screws at the top and the (2) supplied 1” machine screws and the 5/16” white nylon spacers at the bottom.
Wiring and Connections
Route all wires and cable at this time. Install wiring and cables according to the
If applicable, remove the console lid to allow access to the two screws that secure the rear portion of the console. Remove the two screws and reassemble the console lid. Open the cup holder and find and remove the four screws attaching the rear portion of the console.
Pull firmly on the rear portion of the console to release the snap clips. Disconnect the wiring to the HVAC controls, rear radio controls, and the 12 volt power port.
Remove the four screws attaching the radio controls and the four screws attaching the rear air controls
(if equipped) to the back of the console. Save for reinstallation in the video console.
Expedition & Navigator
Expedition XLT Console
instructions provided with electronic equipment.
Installation of Video Console
Install the supplied mounting brackets to the factory console(refer to picture at right). Secure the mounting brackets to the mounting tab using the supplied #8 x 1/2” sheet metal screws through the bracket and into the factory speed clip. Notice that the mounting brackets are mirror images of each other and therefore have to be installed on their respective sides of the console.
Make all electrical connections, including rear radio
controls and the rear air controls (if equipped). Slide the video console onto the back of the factory console, making sure that it is as far down as
Prepare Video Console
possible. Mark and
Prepare the monitor for installation by sliding the small studded bracket into the back panel of the monitor. Run the monitor data cable through the
For consoles with rear air controls, install the air controls mounting brackets onto the rear air control. (see pictures at right) With the brackets installed correctly the middle of the bracket should be flush with the face of the air control. Secure the bracket through the holes in the air control and into the metal bracket using the supplied #6x1/4” sheet metal screws.
Air Control
Mounting Bracket
the upper part of the video housing as a guide. Secure the video housing to the console using the (4) supplied #8 x 1/2” sheet metal screws.
Final Steps
Reinstall all previously removed factory components and panels.
Turn on and test everything.
(If the system doesn’t work properly, recheck all connections and fuses.)
The install of the video system is now complete.
Rev |