Marshall electronic V-R201-IMD-TE Compatible Input Formats, On-Screen Menu, Structure Overview

Compatible Input Formats

The following SDI standards are supported by the V-R201-IMD-TE:

525i, 625i

1035i/60, 1035i/59.94 1080i/60, 1080i/59.94, 1080i/50 1080psF/24, 1080psF/23.98 720p/60, 720p/59.94, 720p/50

On-Screen Menu

STRUCTURE OVERVIEW

On-Screen Menu (continued)

OSD CONFIGURATION SUBMENU (continued)

■OSD Tally

Use this setting to choose how tally is displayed on the screen. The available OSD Tally options depend on the Tally Source selected in the IMD Configuration submenu (see page 19).

When the Tally Source is set to Standard (contact closure), OSD Tally can be set to Off, RGY, RG, or GR:

•	Off	On-screen tally is disabled
•	RGY	Red, yellow, or green tally signals are indicated at both the bottom left and bottom right corners of the
		screen. Two or three colors are shown simultaneously by subdividing each tally indicator
•	RG	Red tally is shown at the bottom left of the screen, and green is shown at the bottom right.
•	GR	Green tally is shown at the bottom left of the screen, and red is shown at the bottom right.

The following diagrams show RGY, RG, and GR OSD Tally modes:

	Marker	Marker 16:9		Off, 95%, 93%, 90%, 88%, 80%, 1.85:1, 2.35:1, 4:3, 14:9, 13:9
		Marker 4:3		Off, 95%, 93%, 90%, 88%, 80%
	Setup	Marker Backgrd		Off, 50% Gray, Black
		Center Marker		Off, On
		CTemp/Gamma		55K, 65K, 93K, Linear
	Video	Monochrome		Off, On
		Blue Only		Off, On
	Config	Pixel to Pixel		Off, On
		Aspect Ratio		4:3, Scaled 4:3, 16:9, Full Screen
		Curtain Color		Blue, Red, Green, White, Black
		Gray Levels		RGB = 000 - 255 (8 unit steps)
		Function 1		Marker, Center Marker, Marker Background, IMD, Time Code, OSD Tally, Audio
				Monitor, Aspect Ratio, Pixel to Pixel, CTemp/Gamma, Blue Only, Monochrome
	System	Function 2		Marker, Center Marker, Marker Background, IMD, Time Code, OSD Tally, Audio
				Monitor, Aspect Ratio, Pixel to Pixel, CTemp/Gamma, Blue Only, Monochrome
	Config
		Load Config		Mfg, User 1, User 2, User 3, User 4, User 5, User 6
		Save Config		User 1, User 2, User 3, User 4, User 5, User 6
		Main Board		(Main board firmware version number displayed)
		Keypad		(Keypad firmware version number displayed)
		CPLD		(CPLD firmware version number displayed)
Main		IMD State		Off, On
	OSD	Status Display		Off, On
		OSD Tally		Off, RGY, RG, GR, IMD
	Config	LED Tally		Off, On
		Anc. Time Code		Off, LTC, VITC
		Audio Monitor		Off, On
		IMD Protocol		Marshall, Image Video, TSL v4.0, Marshall-IV
		IMD ID #	000-255
		IMD Group #	001-254
	IMD	IMD Name (S/N)		User Defined (16 chars max.)
		IMD Baud Rate	300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200
	Config	IMD Fixed Align		Center, Right, Left
		IMD Fixed Color		Red, Green, Yellow
		IMD Fixed Str		User Defined (16 chars max.)
		Tally Source		Standard, Image Video HW, Image Video 422, Standard + IV422, TSL/Marshall 422
		IMD Tally Mode		T1, T2, T1T2, T2T1, T1-, T2-, T1T2-, T2T1-

		00:00:00:00
(red)	IMD Text		(red)

RGY mode: single color activated

		00:00:00:00
(red)	IMD Text		(red)
(green)			(green)
RGY mode: two colors activated
		00:00:00:00
(red)	IMD Text		(red)
RG Mode: both colors activated
		00:00:00:00
(red)	IMD Text		(red)

		00:00:00:00
(red)	IMD Text	(red)
(yellow)		(green)
(green)
		(yellow)

RGY mode: three colors activated

	Serial Chars	Rx, Tx
	Serial Errors	P, F, O
Service	Packets	Rec, Exe
	Packet Errors	CRC, Err
	Last Command	R, E
	Software State	000:000 1010111

		GR Mode: both colors activated
When the Tally Source is set to TSL/Marshall 422, OSD Tally can be set to Off or IMD:
•	Off	On-screen tally is disabled
•	IMD	Red, yellow, and green tally is displayed according the protocol commands. Green, red, and yellow colors
		are shown individually on either the bottom left or right of the screen.

8 17