Before mounting Press, Fuse blows, Sound is distorted

KS-FX701/KS-FX601 KS-F501

Installation/Connection Manual

ØVO	O²ÒÒ
GET0009-002A	qO
GET0009-002A
[U]

ENGLISH

• This unit is designed to operate on 12 volts DC, NEGATIVE •		12V
ground electrical systems.

0900HISFLEJES

	J C
	V	EN, CH, AR

			wÐdŽ
d?ýU?³ w?zUÐd?N?	u?Ð q?L?F?O?	u	•
ÆV	—Qð WOzUÐdN	u	DC

INSTALLATION (IN-DASH

uKÐUð ‡qš«œ ® “UN'« VO dð

MOUNTING)

©…—UO

• The following illustration shows a typical installation. However,

•

d²

d?Þ w

u²

ÒO³¹ •

you should make adjustments corresponding to your specific

w?²? —U?O?

car. If you have any questions or require information regarding

JVC

’uB

uKF* WłUŠ Ë«

«—U„UM¼ ÊU«–« ÆUNJK²9

installation kits, consult your JVC car audio dealer or a company

W??O?ðu?B?

e??N?łô« Ÿ“u?

—U??A??²?Ý« v?łd??¹ ¨V?O? d??²?

Ëœ«

supplying kits.

«Ëœô« …cN

“u*« W dA

JVC

W —U

—UO

1 Before mounting: Press

(Control Panel Release) to

!"#$%

©rJ×² « WŠu d¹d% —“®

—e « jG{« ∫VO d² « q³

detach the control panel if already attached.

ÆUIÐUÝ W u

u X½U

«–« rJ×² « WŠu

qBH

* When shipped from the factory, the control panel is packed

Æ‚ËbMB « qš«œ rJ×² « WŠu l{Ë - ¨lMB*« s

s×A « bMŽ*

in the hard case.

ÆWM¹e « WŠu

Ÿe½« ≤

2 Remove the trim plate.

3 Remove the sleeve after disengaging the sleeve locks.

Æw «u « qJON «

U²³¦ qB bFÐ w «u « qJON « Ÿe½« ≥

1 Stand the unit.

ÆÍœuLŽ qJAÐ “UN'« n Ë«

Ë« —d?Cð Âb?Ž s?

b Q?ð ¨“UN?'« nO? uð b?MŽ ∫W?EŠö?

Note: When you stand the unit, be careful not to damage

Æ“UN'« s WOHK)« WN'« w œułu*« “uOH « ·öð«

the fuse on the rear.

u¼ U?L?

¨w?

«u? « qJ?O?N? «Ë “UN?'« 5?Ð 5?²?

*« q?šœ«

≤

2 Insert the 2 handles between the unit and the sleeve, as

illustrated, to disengage the sleeve locks.

Æw «u « qJON «

U²³¦

qBH

¨qJA « w 5³

3 Remove the sleeve.

Æw «u « qJON « Ÿe½«

≥

Note: Be sure to keep the handles for future use after

q???ł« s??

U??? U??

*« v??K???Ž W??E??? U??;« w???łd??¹ ∫W???E??Šö???

installing the unit.

Æ“UN'« VO dð bFÐ UIŠô ‰ULF²Ýô«

4 Install the sleeve in the dashboard.

Æ…—UO

« uKÐUð qš«œ w «u « qJON « V — ¥

* After the sleeve is correctly installed in the dashboard,

qJA?Ð …—UO

« u?KÐUð qš«œ U?OK

w «u? « qJON? « VO dð b?FÐ *

bend the appropriate tabs to hold the sleeve firmly in place,

w «u « qJON « XO³¦²

VÝUM

qJAÐ WM _« wMŁ« ¨`O×

as illustrated.

ÆqJA « w

5³

u¼ U?L

¨`O×B « ÊUJ*« w

rJ× qJAÐ

5 Fix the mounting bolt to the rear of the unit’s body and place

bFÐË “UN'« qJO¼ s

WOHK)« WN'UÐ VO d² « —UL

X³ÒŁ µ

the rubber cushion over the end of the bolt.

6 Do the required electrical connections explained on the back

Æ—UL

*« W¹UN½ ‚u WOÞUD*« …uA(« l{ p –

nKš ÕËdA u¼ UL

WÐuKD*« WOzUÐdNJ «

öO u² « qLŽ« ∂

of this instructions.

7 Slide the unit into the sleeve until it is locked.

ULOKF² « Ác¼

Æ`O×

qJAÐ X³¦¹ v²Š w «u « qJON « qš«œ “UN'« qšœ« ∑

8 Attach the trim plate.

9 Attach the control panel.

ÆWM¹e « WŠu

VÒ— ∏

ÆrJ×² « WŠu

VÒ— π

Handle

Fuse

“uOH

Slot

dOG Òoý

Rubber cushion

		WOÞUD*« …uA(«
	Sleeve	4
	Sleeve
	w u	7
		7
8		4 *

Sleeve

Trim plate

WM¹e u

Lock plate

XO³¦²W×OH

Dashboard

…—UO

184	mm
	mm
5	53	mm
		mm

Mounting bolt

VO d²

6 See the back page for electrical connections.

	qł« s
	ÆWOzUÐdNJ
	10	1
2	3	1
	3	1
		1
		2
		3
		4
		5

TROUBLESHOOTING

•The fuse blows.

* Are the red and black leads connected correctly?

•Power cannot be turned on. * Is the yellow lead connected?

•No sound from the speakers.

* Is the speaker output lead short-circuited?

•Sound is distorted.

*Is the speaker output lead grounded?

*Are the “–” terminals of L and R speakers grounded in common?

•Unit becomes hot.