Cobra Electronics 29 WX NW BT specifications Bluetooth

Page 8

Operation

Operation

To Answer Calls

Bluetooth®

Note

When cell phone calls are in progress using the Bluetooth feature, the CB functions of the unit are disabled.

Note

If no further pairing steps are taken, the unit will time-out and return to Standby after five minutes. During the pair- ing process, press and release the BT Button to can- cel the pairing process.

Bluetooth

Calls on a Bluetooth enabled cell phone can be routed through the 29 WX NW BT speaker or external speaker accessory.

C H 1 9

BT LED

Indicator

 

C H 9

RX/TX ANT

WX

 

N O R

 

BT Button

To Pair with a Cell Phone

1With 29 WX NW BT power On, press and hold the BT Button for six seconds to enter Standby mode. A tone will sound and the BT LED will flash for one minute to confirm entry

to Standby.

2From Standby,press and hold the BT Button for four seconds to enter Pairing mode.

A.First time pairing with a cell phone:

I.A tone will sound and the BT LED will flash rapidly to confirm Pairing mode.

II.Follow the cell phone manufacturer's instruction to enable its Bluetooth function and enter the PIN (Personal Identification Number)0000.

III.Successful pairing will be indicated by a tone and brief flashing of the BT LED to confirm entry to Connected mode.A pair record will also be established for subsequent connections.

B.Subsequent pairings with a cell phone:

I.Follow any cell phone manufacturer instructions, if needed, to enable the Bluetooth function.

II.Successful pairing will be indicated by a tone and brief flashing of the BT LED to confirm entry to Connected mode.

1Press and release the BT Button when the cell phone ring is heard through the 29 WX NW BT speaker. The BT LED will light steadily to indicate a call is in progress.

2Speak into the 29 WX NW BT microphone.The CB function of the unit and PTT Button will be disabled while a call is in

3progress.

End the call by press and release of the BT Button. A tone will sound and the BT LED will flash briefly.

To Initiate Calls

1Dial a number according to the cell phone manufacturer’s instructions. The key press and other tones will be heard through the 29 WX NW BT speaker.

2Press Send on the cell phone. The BT LED will light steadily to indicate a call is in progress; and after a few seconds, you will hear the ring tone for the number you dialed.

3Once connected, speak into the 29 WX NW BT microphone.

4End the call by press and release of the BT Button. The BT LED will flash briefly.

5Redial a number by press and hold of the BT Button for two seconds. A tone will sound; and after a few seconds, you will hear the ring tone for the number you dialed.

To Enable or Disable Voice Dialing

If the paired cell phone supports voice dialing, press and release the BT Button twice to toggle between enabling and disabling this feature.

ToTurn Off The Bluetooth Function

Press and hold the BT Button for six seconds to turn off the Bluetooth function. Two short tones will sound and the BT LED will turn Off and remain Off.

To Re-pair The 29 WX NW BT To The Cell Phone

If pairing is lost while the 29 WX NW BT power is On,press and hold the BT Button for four seconds to re-pair with the cell phone.

If the 29 WX NW BT is turned Off,it will retain the Bluetooth address and automatically re-pair with the last cell phone used when

it is turned back On.

Note

For best audio quality while using the Bluetooth feature, place your cell phone at least 12 inches away from the

29 WX NW BT.

Note

The external microphone can be plugged into the rear of the unit and clipped to a pocket or lapel for hands-free speech during calls.

When the external microphone is plugged in, the main microphone will not pick up speech during calls but will be fully functional for CB operation.

14

15

Image 8
Contents How to Use Your Cobra 29 WX NW BT Features of This ProductInstallation LocationLocationMounting and Connection Mounting and ConnectionInstallation Marine Installation Antennas Ignition Noise InterferenceCB Antenna CB AntennaSetting Channel Selector Setting Channel SelectorOperation Turning OnWhile holding mic Button adjust Calibrate For SWR Standing Wave RatioCalibrate for SWR Standing Wave Ratio Select channelMeter Selecting a ChannelTo Receive Bluetooth BluetoothRF Gain Control RF Gain Control Noise Limiter SwitchOFF Noise Blanker Automatic Dimmer Switch Dimmer Switch Setting SquelchSetting Squelch Squelch is the control gatefor incoming signalsSetting Dynamike Setting DynamikeTransmit Select desired channelOutput outgoing signal while transmitting RF MeterExternal Speaker RF MeterSet CB/PA switch to PA position Adjust PA speaker volume with the Dynamike controlPA Public AddressWhat is Weather Radio Weather Radio ChannelsWeather Information Operating Weather Channel SelectorHome And Office Set-Up Temporary Mobile Set-Up Base Station Operation From 120V AC House CurrentTemporary Mobile Set-Up Base Station Operation From 120V AC House CurrentHow Your CB Can Serve You Few Rules You Should Know Channel Emergency MessagesCB 10-Codes CB 10-CodesFrequency Ranges WX NW BT Specifications Limited Two Year Warranty Optional Accessories Cobra Electronics CorporationOrdering From U.S.A For Credit Card OrdersCB Story Controls and Indicators Our Thanks to You Cobra Customer ServiceCustomer Support Back Side

29 WX NW BT specifications

The Cobra Electronics 29 WX NW BT is a versatile and powerful CB radio designed specifically for truckers, outdoor enthusiasts, and anyone in need of reliable communication over long distances. Known for its advanced features and user-friendly interface, this model stands out in a crowded market of CB radios.

One of the key features of the Cobra 29 WX NW BT is its built-in Bluetooth technology, which allows users to connect their smartphones and other devices for hands-free operation. This functionality is invaluable for keeping drivers focused on the road while staying connected to their networks. The Bluetooth feature provides convenient access to calls, enabling a safer driving experience.

The radio offers a robust range of channels, featuring 40 CB channels and 10 NOAA weather channels. This ensures that users can stay informed about severe weather conditions, crucial for long-haul truck drivers and outdoor adventurers. The NOAA weather channel functionality provides instant alerts about weather changes, helping users make informed decisions while on the road.

In terms of range, the Cobra 29 WX NW BT is equipped with a high-efficiency RF design and a powerful PA (Public Address) function. This adds an extra layer of communication capability, allowing users to broadcast their messages to others in the vicinity without the need for additional equipment.

The 29 WX NW BT also includes customizable settings such as adjustable squelch control, which helps to filter out background noise, and RF Gain control that allows users to improve the reception of distant signals. With its 4-pin microphone connector, the unit supports a variety of microphones for users' preferences in audio clarity and performance.

Another notable feature is the large, easy-to-read LCD display, which provides clear visibility of channel numbers and signal strength. The backlighting ensures that the information is visible, even in low-light conditions. The radio also boasts a rugged build, designed to withstand the rigors of life on the road.

In summary, the Cobra Electronics 29 WX NW BT combines modern technology with user-friendly features, making it an excellent choice for those who require reliable communication and safety on their journeys. With Bluetooth connectivity, weather channel access, and customizable settings, it is a robust tool for anyone in need of a dependable CB radio.