M5300 -EX Front Panel Features

Power Button

Press and hold for 2 sec- onds to turn Bank 2 and Bank 3 outlets ON or OFF. This switch is bypassed if the rear panel DC Trigger input is being used.

Power LEDs

Indicates the status of the rear panel outlets. LEDs for each outlet bank will be lit when the outlets are turned ON. They will flash during the start- up and shutdown process.

Wiring OK LED

Normally On. Indicates that the wall outlet is properly grounded and Line/Neutral polarity is correct.

Meter Dimmer

Pushbutton control for meter LED brightness. Cycles between Off, Low, Medium and High.

Voltmeter

Digital LED voltmeter indicates incoming line voltages between 90–140VAC.

Convenience

Outlet

Provides a quick con- venient way to plug in components such as camcorders and video game systems.

M5300-EX

VOLTS

BANK 1	BANK 2	BANK 3	WIRING
ALWAYS ON	ON	ON	OK
				METER
POWER AND FILTRATION				LIGHTS

Home Theater Power Conditioner

Unsafe Voltage Indicator

Normally Off. Flashes to indicate that the incoming line voltage is unsafe and the unit has disconnect- ed the power to protect your equipment.

M5300 -EX Back Panel Connection Features

		Outlet Bank 2
		Four switched outlets controlled by the
	Circuit Breaker	front panel Power Button or the DC Trigger
	Circuit Breaker	input. Bank 2 will turn on immediately and
	Automatically opens	input. Bank 2 will turn on immediately and
	Automatically opens	turn off after 10 seconds. EMI/RFI noise fil-
	when the current load	tration is provided by a three-stage balanced
	is greater than 15	Pi filter which also provides noise isolation
	Amps. Push to reset.	from Outlet Banks 1 and 3.

Outlet Bank 1

Four always on outlets. Power will only be turned off under a fault condition. (See specifications for over-voltage and under-voltage thresholds) Power is cleaned by a three-stage balanced Pi fil- ter which also provides noise isolation from Outlet Banks 2 and 3.

Satellite TV
Coax Jacks		Cable TV Coax Jacks
Bidirectional protection cir-		Bidirectional protection cir-
cuit optimized for satellite		cuit optimized for cable TV,
TV signal lines. Do not use		off-air antennas and cable
for cable TV off-air anten-		modem signal lines. Do not
nas and cable modems.		use for Satellite TV.

15 AMP CIRCUIT	BANK 3
BREAKER
	RECEIVER
GROUND
LUG
	DELAY ON
	SUB / AMP
MAIN POWER	HIGH CURRENT
120 VAC/15A

DVD

BANK 2

PRE-AMPAUX / VCR

SWITCHED

	BANK 1
HDTV / MONITOR	DVR
HD CABLE / SAT	DIGITAL RADIO
	ALWAYS ON

	SATELLITE		CATV / ANT
SATELLITE 1	SATELLITE 2	CATV / ANT 1	CATV / ANT 2
		LAN	PHONE
VOLTAGE SENSE	LINE IN	EQUIP.	LINE IN	EQUIP.
TRIGGER INPUT
3 - 24VDC

Main Power

Must be plugged into a properly wired & ground- ed 3-wire outlet

Ground Lug

Provides a common grounding point for equipment with sep- arate ground leads.

Outlet Bank 3

Two switched, high current outlets controlled by the front panel Power Button or the DC Trigger input. Bank 3 has a 5 second turn on delay and turns off immediately. The High Current outlets pro- vide power from a low impedance noise filtration circuit that does not limit the current to your equipment. Its output is noise isolated from all other outlet banks.

Voltage Sense Trigger Input	LAN Jacks
3.5mm (1/8”) Mini-Plug jack.	Protection circuits
Connect to a remote trigger device	for 10/100	baseT
that uses a DC output to trigger a	Ethernet	lines.
startup/shutdown sequence. This	Incoming LAN line
bypasses the front panel power	MUST be plugged
switch. Important, Please Note:	into the LINE jack.
The unit needs to be plugged in,	Patch cord to the
and in the powered OFF state	equipment	MUST
before inserting the DC input trig-	be plugged into
ger mini-plug.	the EQUIP jacks.

Phone Jacks

Protection circuits for standard telephone or pay- per-view lines. Phone cir- cuit is auto-resetting. Incoming phone cord MUST be plugged into the LINE jack. Patch cords to the equipment (satellite receiver, digital video recorder, telephone, etc.) MUST be plugged into the EQUIP jacks.

Note to CATV Installers:

This reminder is provided to call attention to Article 820-40 of the NEC. That article provides specific guidelines for proper grounding.It specifies that the cable ground shall be connected to the grounding system of the building and as close to the point of entry as practical.