Sony MDS-JD320 Section Electrical Adjustments, Precautions for Checking Laser Diode Emissinon

Page 16

SECTION 5

ELECTRICAL ADJUSTMENTS

5-1. PRECAUTIONS FOR CHECKING LASER DIODE EMISSINON

To check the emission of the laser diode during adjustments, never view directly from the top as this may lose your eye-sight.

5-2. PRECAUTIONS FOR USE OF OPTICAL PICK- UP (KMS-260A)

As the laser diode in the optical pick-up is easily damaged by static electricity, solder the laser tap of the flexible board when using it. Before disconnecting the connector, desolder first. Before connecting the connector, be careful not to remove the solder. Also take adequate measures to prevent damage by static electricity. Handle the flexible board with care as it breaks easily.

pick-up

flexible board

 

laser tap

Optical pick-up flexible board

 

Optical

 

BD Board

 

Pick-up

 

 

 

 

IC171

D101

IC101, IC121, IC192

 

 

 

 

 

 

 

1.Temperature

 

 

 

 

compensation

G

Â

Â

Â

offset adjustment

 

 

 

 

 

 

 

 

 

2. Laser power

Â

Â

G

Â

adjustment

 

 

 

 

 

 

 

 

 

3. Traverse

Â

Â

G

Â

adjustment

 

 

 

 

 

 

 

 

 

4. Focus bias

Â

Â

G

Â

adjustment

 

 

 

 

 

 

 

 

 

5. Error rate check

Â

Â

G

Â

 

 

 

 

 

5-3. PRECAUTIONS FOR ADJUSTMENTS

1)When replacing the following parts, perform the adjustments and checks with Âin the order shown in the following table.

2)Set the test mode when performing adjustments. After completing the adjustments, exit the test mode.

3)Perform the adjustments in the order shown.

4)Use the following tools and measuring devices.

Check Disc (MD) TDYS-1 (Parts No. 4-963-646-01)

Laser power meter LPM-8001 (Parts No. J-2501-046-A)

Oscilloscope (Measure after performing CAL of prove.)

Digital voltmeter

Thermometer

Jig for checking BD board waveform

(Parts No. : J-2501-124-A)

5)When observing several signals on the oscilloscope, etc., make sure that VC and ground do not connect inside the oscilloscope.

(VC and ground will become short-circuited.)

6)Using the above jig enables the waveform to be checked without the need to solder.

(Refer to Servicing Note on page 4.)

Note : When performing laser power checks and adjustment (electrical adjustment), use of the new MD laser power meter 8010S (J-2501-145-A) instead of the conventional laser power meter is convenient.

It sharply reduces the time and trouble to set the laser power meter sensor onto the objective lens of the pick-up.

5-4. CREATING CONTINUOUSLY RECORDED DISC

This disc is used in focus bias adjustment and error rate check. The following describes how to create a continuous recording disc.

1.Insert a disc (blank disc) commercially available.

2.Rotate the AMS knob and display “CREC MODE”.

3.Press the YES button again to display “CREC MID”. Display “CREC (0300)” and start to recording.

4.Complete recording within 5 minutes.

5.Press the EDIT/NO button and stop recording .

6.Press the ¤EJECT button and remove the disc.

The above has been how to create a continuous recorded data for the focus bias adjustment and error rate check.

Note :

• Be careful not to apply vibration during continuous recording.

— 16 —

Image 16
Contents Specifications MDM-3GCFlexible Circuit Board Repairing VarnigTable of Contents DisassemblyDiagrams Exploded ViewsSELF-DIAGNOSIS Function Self-Diagnosis FunctionForced Reset Section Servicing NoteJIG for Checking BD Board Waveform Main Board Component SideRetry Cause Display Mode Fluorescent Display Tube SignsHexadecimal nBinary Conversion Table Section General Location of Parts and ControlsCase and Front Panel Assembly Section DisassemblyBracket T, L and R BD Board SUB ChassisShutter Assembly Over Write HeadSlider Complete Assembly Section Test Mode Operating the Continuous Playback Mode Operating the Continuous Recording ModeNon-Volatile Memory Mode MIDFunctions of Other Buttons Test Mode DisplaysMeanings of Other Displays Section Electrical Adjustments Precautions for Checking Laser Diode EmissinonPrecautions for USE of Optical PICK- UP KMS-260A Precautions for AdjustmentsLaser Power Adjustment Temperature Compensation Offset AdjutmentSpecified Value Traverse Adjustment Traverse WaveformFocus Bias Adjustment Error Rate CheckAdjusting Points and Conneting Points MDS-JE320MDS-JE320 Section Diagrams Block DiagramsOptical PICK-UP Block MainMain Section RECFor printed wiring boards For schematic diagramsWaveform Location Printed Wiring Board BD SectionSemiconductor Schematic Diagram BD /2 See page 26 for Waveforms See page 49 for IC Block Diagrams Printed Wiring Board Main Section Main BoardSchematic Diagram Main /3 MDS-JE320 Schematic Diagram Main /3 Display Board Printed Wiring Board Display SectionEject SW Board Schematic Diagram Display Section Printed Wiring Board Switch Section Schematic Diagram Switch Section IC121 CXD2650R IC Block DiagramsBD section IC101 CXA2523R IC121 CXD2652AR IC152 BH6511FSIC171 XL24C01AF IC192 L88MS33TMain section IC301 LA9615 IC307 CXD8607NIC308 M5218AL IC309 LA5620 IC310 M5293L IC311 LB1641IC PIN Functions IC101 RF Amplifier CXA2523R Pin No Pin Name FunctionMNT0 FOK MNT1 ShckMNT2 Xbusy MNT3 SlocPin No Pin Name Function Tfdr FfdrFrdr FS4IC307 A/D, D/A converter CXD8607N Pin No Pin Name Function TEST2 TEST3Lvdd LvssTimer SW Power DownDaout ChuckMNT2 MNT3LED0 BUS OUTDIG-RST BeepDA-RST Dsel A, Dsel BSection Exploded Views Main SectionFront Panel Section 6059Panel ASSY, Front US,CND Button MainMechanism Deck MDM-3GC 201 202203 204 205 206 207 209 208253 254 259 252257 258 260 271 Section Electrical Parts List TC74ACT540FS Inductor ChipShort InductorControl SW Display Eject SW Main NJM78L06A NJM79L12ASN74HCU04AN Line FilterMDS-JE320 Main

MDS-JD320 specifications

The Sony MDS-JD320 is a MiniDisc recorder that exemplifies the cutting-edge technology of the late 1990s and early 2000s. Designed for both amateur and professional audiophiles, it delivers superior sound quality and an array of features that enhance user experience and functionality. Key to its appeal is its remarkable sound reproduction capabilities, which are achieved through Sony's proprietary technologies, including the ATRAC (Adaptive Transform Acoustic Coding) compression format. This format allows for efficient audio storage without sacrificing sound fidelity, ensuring that each recording is as rich and dynamic as the original source.

One of the standout features of the MDS-JD320 is its ability to create, edit, and playback CDs and MiniDiscs with remarkable ease. Thanks to its digital optical input and output, users can connect the device to various audio sources, such as CD players or mixing boards, to make high-quality recordings. The device supports various recording modes, including long play, which enables users to extend their recording time without significant compromise on audio quality.

The MDS-JD320 also boasts a user-friendly interface, which includes an LCD display that conveniently shows essential information such as track numbers, remaining time, and recording mode. Furthermore, an intuitive remote control offers added convenience, allowing users to navigate through their music collections without having to physically interact with the device.

In terms of connectivity, the MDS-JD320 features not only digital inputs and outputs but also analog connections, making it versatile for various setups. Additionally, the device includes extensive editing features, such as track splitting, combining, and renaming, empowering users to customize their recordings easily.

Moreover, the MDS-JD320's compact design fits seamlessly into any audio setup, making it an attractive choice for both home recording enthusiasts and professionals. Its durable build quality ensures longevity, while its performance continues to impress even in today's digital audio landscape.

With its powerful combination of advanced technologies, ease of use, and high-quality audio performance, the Sony MDS-JD320 remains a sought-after component for collectors and audiophiles alike, representing an enduring legacy in the field of portable digital media solutions.