Gemini TT-03 manual Introduction, Features, Precautions, Parts Checklist, Assembly & SET-UP

Page 4

INTRODUCTION:

Congratulations on purchasing a Gemini TT-03fully manual high torque turntable. This state of the art turntable includes the latest features. Prior to use, we suggest that you carefully read all the instructions.

FEATURES:

-Fully Manual Direct Drive Turntable

-Super high torque (2.2 kg) direct drive turntable

-+/-10% variable pitch slide control

-Solid aluminum platter with easy glide grooves

-Straight tone arm for superior tracking

-Tone arm height adjustment up to 6 mm with lock

-Fully adjustable counter weight & anti-skating controls

-LED illuminated soft touch start/stop & RPM buttons

-33/45/78 RPM

-Push button quartz lock w/ LED

-Target light with RCA connector

-Removable head shell

-Felt slip mat included

-Detachable RCA & ground cables

PRECAUTIONS:

1.Read all operating instructions before using this equipment.

2.The apparatus should not be exposed to dripping or splash- ing, and no objects filled with liquids such as vases should be placed on the apparatus.

3.To reduce the risk of electrical shock, DO NOT OPEN THE UNIT. Please contact the Gemini Service Department or your authorized dealer to speak to a qualified service technician.

IN THE USA ~ IF YOU EXPERIENCE PROBLEMS WITH THIS UNIT CALL GEMINI CUSTOMER SERVICE AT: 1 (732) 738-9003. DO NOT

ATTEMPT TO RETURN THIS EQUIPMENT TO YOUR DEALER.

4.Tone Arm bearings are factory set and sealed. Any attempt at adjustment will void the warranty.

5.Be sure that all AC power is OFF while making connections.

6.Cables should be low capacitance, shielded and of proper length. Make sure that all plugs and jacks are tight and properly connected.

7.Always, begin with the audio level faders/volume controls set at minimum and the speaker volume control(s) set to OFF. Wait

8to 10 seconds prior to turning up the speaker volume to pre- vent the transient "POP" that could result in speaker/crossover damage.

8.DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

9.DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR SWITCHES.

PARTS CHECKLIST:

Please make sure the following parts are included with your TT-

03:

Turntable

unit

1

Turntable

platter

1

Slipmat

1

Counterweight

1

Headshell

with cartridge

1

RCA target light……………………………….............…………1

ASSEMBLY & SET-UP:

SEE FIG. 3 FOR PART NUMBERS AND LOCATIONS.

VOLTAGE SELECTION:

Rotate the PLATTER (2) until the VOLTAGE SELECTION SWITCH (3) (located on the TURNTABLE BASE (1)) is visible through one of the platter holes. Make sure that the VOLTAGE SELECTOR SWITCH (3) is set to the correct voltage.

WARNING: IF YOU TRY TO OPERATE THE TURNTABLE WITH THE INCOR- RECT VOLTAGE SETTING, IT CAN DAMAGE YOUR TURNTABLE.

TURNTABLE INSTALLATION:

1.Put the SLIPMAT (4) on the PLATTER (2).

2.Set the TURNTABLE BASE (1) on a flat, level surface free of vibration. Use the turntable feet to stabilize the unit horizontally.

3.Try to place the unit as far away from the speakers as possi- ble.

4.Keep the unit away from direct exposure to the sun, heat, moisture or dirt.

5.Keep the unit well ventilated.

CARTRIDGE INSTALLATION: (SEE FIG. 1)

Because all cartridges have their own designs, please refer to your particular cartridge's instructions to insure proper installa- tion. If you are using a pre-mounted or integrated cartridge, you can jump ahead to HEADSHELL INSTALLATION.

1.Connect the lead wires to the cartridge terminals. For your convenience, the terminals of most cartridges are color-coded. Connect each lead wire to the terminal of the same color. In case your cartridge is not marked the positive leads are the ones on top negative below, left are left, and right is right.

White (L+)

Left Channel +

Blue (L-)

Left Channel -

Red (R+)

Right Channel +

Green (R-)

Right Channel -

2.Mount the cartridge in the HEADSHELL (5) and tighten it with the screws included with the cartridge.

HEADSHELL INSTALLATION:

Insert the HEADSHELL (5) into the front of the tubular TONE ARM (7). While holding the HEADSHELL (5) firmly in a horizon- tal position, turn the LOCKING NUT (6) counter clockwise until the HEADSHELL (5) is locked in place.

COUNTERWEIGHT INSTALLATION: (SEE FIG. 2)

1.Slide the COUNTERWEIGHT (8) onto the rear of the TONE ARM (7) with the numbered stylus gauge facing forward.

2.Twist the COUNTERWEIGHT (8) counter clockwise lightly, to screw it onto the rear of the TONE ARM (7).

ADJUSTING HORIZONTAL ZERO (0) BALANCE AND STYLUS PRESSURE:

1.Without touching the stylus tip, remove the stylus protector (if your cartridge has a detachable one).

2.Release the ARM CLAMP (10) and lift the TONE ARM (7) off the ARM REST (11).

3.Counter clockwise advancement of the COUNTERWEIGHT

(8) will cause the cartridge side of the TONE ARM (7) to be low- ered; turning it clockwise will cause the opposite. Turn the COUNTERWEIGHT (8) clockwise or counter clockwise as need- ed until the TONE ARM (7) is balanced horizontally. You can

(4)

Image 4
Contents Direct Drive Straight ARM Turntable Multi Language Instructions TT-03 Features PrecautionsParts Checklist Assembly & SET-UPSpecifications Operating InstructionsEinführung AusstattungTeileliste AufbauanleitungBedienungsanweisung Technische DatenMontaje Y Configuración IntroducciónCaracterísticas PrecaucionesInstrucciones DE Operación EspecificacionesMontage & Installation CaracteristiquesMises EN Garde Liste DES Pieces Livrees Avec LappareilConnections Instructions DutilisationTel 732 738-9003 Fax 732