Package Contents, Cup Holder Mounting | Avaya SM523-G instruction

SM523-G

Cup Holder Mount with Flexible Goosneck Shaft with Slim-Grip™ Smartphones

SM050-2 Slim-Grip™ Universal Phone Holder

88mm expandable to 138mm with Extra Long Support Legs

	SP-SM050-LF	GN033-SBH
	SP-SM050-LF	Cup Holder Mount
	Extra Long	Cup Holder Mount
	Extra Long
	Support Legs
	(2 Pack)

Package Contents:

(1)GN033-SBH - 5” Cup holder mount with flexible gooseneck shaft

(1)SM050-2 Universal phone and portable device holder

(1)SP-SM050-LF - Extra Long Support Legs (2 Pack) for larger phones

Holder included is Universal, designed to fit nearly ALL non-flip mobile phones regardless of whether a protective case or silicone sleeve is attached to the phone.

•	Most smartphones, mobile phones, and cell phones	•	Palm - All non-flip models
	having heights between 80mm and 138mm tall	•	LG Mobile Phones - All non-flip models
•	Apple iPhone - All models	•	Samsung - All non-flip models
•	RIM BlackBerry - All non-flip models	•	Sony Ericsson - All non-flip models
•	HTC Phones - All non-flip models	•	Sanyo - All non-flip models
•	Motorola Phones - All non-flip models	•	Pantech - All non-flip models
•	Nokia Mobile Phones - All non-flip models	•	Google - All non-flip models

No tools required for installation.

Note: mount may not work with adjustable, “pop out” cup holders or oversize cup holder openings found in full-size pickup trucks.

!Do not place mount in or near an air bag deployment zone or where it will obstruct view of the road.

All brand names and product names are trademarks or registered trademarks of their respective owners.

Cup Holder Mounting

Step 1. Connect the gooseneck shaft (A) to the cup holder base (B) by aligning the groove on the base to the ridge inside of the bottom of the shaft.

(A) Cup Holder Neck

(B) Cup Holder Base

Step 2. Place the Universal Cup Holder Mount into the designated cup holder in the vehicle. Adjust the thumb wheel adjuster (C) to open or close the cup holder prongs to fit in the cup holder.

For oversize cup holder openings or the adjustable “pop out” cup Step 3. holders use the optional self-adhesive side support pads (D). Install

Install the Support Legs to the Holder

Step 1. Insert the holder support legs (A) by sliding them into the support leg grooves (B) on the top and bottom of the holder.

A B

iPhone Holder Attachment

Step 1. Adjust the angle of the dual T head by tightening the adjustment nut at the top of the cup holder shaft (A).

Step 2. Install the iPhone holder to the shaft by inserting the dual T-tabs

(B)on the shaft into the T-slots (C) on on the back of the holder.

the pads by removing the adhesive backing and placing it on the flat surface side of the cup holder support leg.

	(D) Optional	OPEN
	(D) Optional
	support	CLOSE
	pads	CLOSE
	pads

(A) Angle

Adjustment

Nut

(B) Cup Holder Shaft T-tabs

!Safety Precautions

Do not install Arkon products over an air bag cover or within the air bag deployment zone. Arkon Resources, Inc. assumes no responsi- bility of liability for injury or death as a result of car crashes and / or air bag deployment.

Arkon is not responsible for any damages caused to your car, your device, or yourself due to the installation or use of this pedestal mount.

	The Mobile Mounting Specialists™
Consumer Hotline:		www.arkon.com
USA	(800) 841-0884	Arcadia, CA 91006 USA
INT’L	⁜(626) 254-9005	Designed in USA Made in Taiwan & China
Monday - Friday 9 am - 5 pm, PST		© Copyright 2010 Arkon Resources, Inc.