Weslo WLTL39092 Harness is not pinched, Tighten all parts used in this step and in step

Page 6

3.Cut the plastic tie holding the cage nut in the upper end of Left Handrail (2).

Position the Left Handrail (2) on the left Upright (14). The lower end of the Left Handrail should be on the outside of the Extension Leg (41) as shown. Thread a Handrail Bolt (15) with a Handrail Washer (16) into the left Upright and the Left Handrail. Do not tighten the Handrail Bolt yet.

Attach the lower end of the Left Handrail (2) to the Extension Leg (41) with a 3 1/2” Handrail Bolt (59), a 5/16” Washer (32), and a Handrail Nut (82). Do not tighten the Handrail Bolt yet.

Refer to the inset drawing. Attach the Latch Catch (88) and the Latch Catch Spacer (74) to the left side of the Frame (70) with two Screws (55). Do not to overtighten the Screws or you will damage the Latch Catch.

4.Have a second person hold the Console Base (6) and the Right Handrail (57) near the right Upright (14) as shown. Fold the Wire Harness (26) as shown and insert the folded Wire Harness into the Right Upright.

Cut the indicated plastic tie off the Handrail (57).

Make sure that the Wire Harness (26) is inside of the bracket on the Right Handrail (57) and insert the bracket into the right Upright (14). Make sure that the Wire

Harness is not pinched.

5.Thread a Handrail Bolt (15) with a Handrail Washer (16) into the right Upright (14) and the Right Handrail (32). Do not tighten the Handrail Bolt yet.

Attach the lower end of the Right Handrail (32) to the Extension Leg (41) with a 3 1/2” Handrail Bolt (59), a 5/16” Washer (32), and a Handrail Nut (82).

Tighten all parts used in this step and in step 3.

6.Attach the Console Base (6) to the Left and Right Handrails (2, 57) with four Screws (55).

7.Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a safe place. The allen wrench is used to adjust the walking belt (see page 13). To protect the floor or carpet, place a mat under the treadmill.

3

 

 

 

 

 

15

 

 

 

16

 

 

 

2

 

 

 

14

 

 

 

70

 

74

 

41

82

 

 

 

55

88

32

 

 

 

59

 

4

 

 

 

 

 

6

 

Bracket

 

 

 

 

Plastic Tie

 

 

57

26

 

 

14

 

 

 

 

5

 

 

 

 

 

15

 

 

 

16

 

 

 

32

 

 

 

14

 

 

82

41

 

 

 

 

 

 

32

 

 

 

59

 

6

 

 

 

57

 

 

 

 

 

6

 

 

 

55

 

 

 

2

 

 

 

 

55

6

Image 6
Contents QUESTIONS? Model No. WLTL39092 Serial NoCustomer HOT Line Table of Contents Important PrecautionsPage Before YOU Begin Left Side Right SideAssembly Driver , two adjustable wrenches , and scissorsExtension Leg Screw while tightening it Harness is not pinched Tighten all parts used in this step and in stepOperation and Adjustment HOW to Plug in the Power CordPerformant Lubetm Walking Belt Insert the key fully into the power switch Diagram of the ConsoleBattery Installation Step by Step Console OperationAdjust the incline of the treadmill as desired Reset the console and start the walking beltReset position be- fore the walking belt Can be restarted Follow your progress with the monitor modesHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Maintenance and TROUBLE-SHOOTING Problem The power turns off during useTop Problem The walking belt slows when walked on Problem The walking belt is off-centerProblem The walking belt slips when walked on Conditioning Guidelines Exercise IntensityWorkout Guidelines Suggested Stretches Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Remove this Exploded Drawing and Part List from the Manual R0601A Key No. Qty DescriptionExploded