Weslo WLTL39201 Maintenance and TROUBLE-SHOOTING, Problem The power turns off during use

Page 12

MAINTENANCE AND TROUBLE-SHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll- free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppres- sor is plugged into a properly grounded outlet (see page 7). Use only a single-outlet surge sup- pressor that meets all of the specifications described on page 7. Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c. Check the circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c. Remove the key from the console. Reinsert the key fully into the console.

d. Unplug the power cord, wait for five minutes, and then plug the power cord back in.

e. If the treadmill still will not run, please call our Customer Service Department, toll-free.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Check the batteries in the console. If the batteries need to be replaced, see assembly step 6 on page 6. Most problems are the result of drained batteries.

b. Remove the six screws from the hood. Carefully remove the hood. Locate the Reed Switch (89) and the Magnet (88) on the left side of the Pulley (90). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8”. If nec- essary, loosen the Screw (31) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

b

 

1/8”

90

89

 

 

88

31

 

Top

 

View

 

12

Image 12
Contents QUESTIONS? Model No. WLTL39201 Serial NoCustomer HOT Line Table of Contents Important PrecautionsPage Before YOU Begin BackRight Side Assembly Your own phillips screwdriver and adjustable wrenchAbove. Do not tighten the Handrail Bolts 1 yet Tighten the Console Screw yet. Then, loosely threadOvertighten the Console Screws. Insert the excess Tighten the four Handrail Bolts 1 used in stepOperation and Adjustment HOW to Plug in the Power CordPerformant Lubetm Walking Belt Diagram of the Console Battery InstallationInsert the key fully into the console STEP-BY-STEP Console OperationTIME/DISTANCE CALS/FAT CalsHOW to Fold and Move the Treadmill Handrail Height AdjustmentHOW to Fold the Treadmill for Storage HOW to Move the Treadmill HOW to Lower the Treadmill for USEMaintenance and TROUBLE-SHOOTING Problem The power turns off during useProblem The walking belt slows when walked on HOW to Measure Your Heart Rate Conditioning GuidelinesExercise Intensity Workout GuidelinesExercise Frequency Suggested StretchesOrdering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Remove this Exploded Drawing and Part List from the Manual Part LIST-Model No. WLTL39201 Qty DescriptionDRAWING-Model