Weslo WLTL211041 user manual Harness, Touch the right Handrail 4 to discharge any static

Page 6

3.If there are plastic ties in the brackets on the Handrails (4), remove the plastic ties. Hold one of the Handrails near the right Upright (38) as shown. Insert the Wire Harness (53) up through the bracket on the Handrail and out of the round hole in the side of the Handrail. If nec- essary, use needlenose pliers to pull the Wire Harness out of the hole. Be careful not to damage the Wire

Harness.

Insert the brackets on the Handrails (4) into the upper ends of the Uprights (38).

Finger tighten four 1” Bolts (16) with Handrail Washers

(40)into the Uprights (38) and the Handrails (4) as shown.

4.Set the Console Base (87) on the Handrails (4). Thread four 3/4” Screws (5) into the Handrails and the Console Base. After you have started all four Screws, tighten the

Screws until they are snug; do not overtighten the Screws. Note: It may be helpful to press down on the top of the Console Base above the Handrails as you tighten the Screws.

See step 3. Firmly tighten, but do not overtighten, the four 1” Bolts (16).

Insert the Wire Harness (53) through the two indicated plastic ties on the Console Base (87) and up through the hole in the Console Base as shown.

5.Hold the Console (11) near the Console Base (87).

Touch the right Handrail (4) to discharge any static.

Next, insert the Wire Harness (53) through the plastic tie labeled C in the drawing at the right.

Locate the two connectors on the Wire Harness (53). Plug the wider connector into the connector labeled A in the drawing at the right (see drawing 5b). The connec- tors should slide together easily and snap into place. If they do not, turn the connector on the Wire Harness and try again. Insert the other connector through the plastic tie labeled D; plug the connector into the connector labeled B (see drawing 5c). IF THE CON-

NECTORS ARE NOT INSERTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.

See drawing 5a. Pull any slack in the Wire Harness (53) through the two ties. Make sure that the end of the Wire Harness indicated by the arrow is routed as shown.

Securely tighten the plastic ties around the Wire Harness. Cut off the end of each plastic tie.

6

3

4

 

 

 

 

Connectors

4

 

16

 

53

 

40

 

 

Bracket

 

 

40

 

16

38

16

 

 

 

40

 

16

38

 

 

4

 

 

 

87

4

 

53

4

 

 

 

 

Plastic Ties

5

 

5

5

11

 

 

A

Tie D

 

Tie C

 

 

87

B

53

4

5a

 

Tie

Tie

53

 

5b

5c

53

A

B

 

 

53

Image 6
Contents QUESTIONS? Model No. WLTL211041 Serial NoTable of Contents Important PrecautionsPage Back Before YOU BeginFront Right SideAssembly Assembly requires the included allen wrenchesExtension Leg Screw while tightening it Harness Touch the right Handrail 4 to discharge any staticPage Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Insert the key fully into the console Diagram of the ConsoleSTEP-BY-STEP Console Operation Pressbelt. the Speed button to start the walkingCalories/Speed Change the incline of the treadmill as desiredFollow your progress with the displays Time/Distance Whenkey. you are finished exercising, removeHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USEMaintenance and Troubleshooting Problem The power turns off during useTop View Problem The walking belt slows when walked on Exercise Intensity HOW to Measure Your Heart RateConditioning Guidelines Workout GuidelinesOrdering Replacement Parts Part Identification Chart Part LIST-Model No. WLTL211041 Qty DescriptionDrawing Limited Warranty Product Warranty Registration