Linear HCI+2 installation instructions Nuts and BOLTS, They will be, Used Again Later

HCI+2	1.	PRODUCT DESCRIPTION	2.	KIT CONTENTS	3. LOOSEN AND DISASSEMBLE TURNBUCKLE
	The Model HCI+2 2-foot “I-rail” extension is designed to be compatible with					HOLD SCREWDRIVER IN
	the Model HCI-12 12-foot chain-drive “I-rail” used in commercial garage door					TURNBUCKLE SLOT
	installations and in carriage house garage door installations.The 2-foot extension,			BOTTOM RAIL SECTION		LOOSEN THE TWO
	when added to the 12-foot “I-rail”, provides a 14-foot long rail for operating high-lift
2-Foot Rail Extension	doors.					TURNBUCKLE LOCKING NUTS
For Use with HCI-12 12-foot “I-beam” Rail	The kit includes two “T-rail” sections that bolt together to form an “I-rail” and			REINFORCING STRAPS (2)
	connect to the main “I-rail” using two reinforcing straps. The kit also includes two
	short lengths of chain to extend the stock chain at the turnbuckle.					UNSCREW AND
Installation Instructions
						REMOVE EACH
						END FROM THE
						TURNBUCKLE
				TOP RAIL SECTION
				1/4-20 KEPS NUTS (5)	NOTE: ONE SIDE OF THE
					TURNBUCKLE IS LEFT-HAND
				1/4-20 x 13/16" CARRIAGE BOLTS (5)
					THREAD, THE OTHER SIDE
					IS RIGHT-HAND THREAD
USA & Canada (800) 421-1587 & (800) 392-0123				EXTENSION CHAINS (2)
(760) 438-7000 - Toll Free FAX (800) 468-1340
www.linearcorp.com
4. REMOVE SPROCKET	5.	REMOVE RAIL BOLT	6.	IDENTIFY TOP AND BOTTOM EXTENSION RAILS	7. ALIGN REINFORCING STRAPS
AFTER THE CHAIN IS LOOSENED,		LOOSEN THE NUTS AND				LINE UP SLOTS ON THE
						REINFORCING STRAPS
REMOVE THE SPROCKET HOLDER		REMOVE THE TWO END		TOP RAIL SECTION
					REINFORCING STRAP #1	WITH THE SLOTS ON THE
FROM THE END OF THE RAIL		BOLTS ON THE RAIL
						STOCK I-RAIL

	NOTE: BE SURE AND KEEP THE
	NUTS AND BOLTS, THEY WILL BE		BOTTOM RAIL SECTION
	USED AGAIN LATER				REINFORCING STRAP #2
			NOTE: BOTTOM RAIL HAS NOTCH ON CORNER!
8. INSTALL FIRST TWO STRAP BOLTS	9. PLACE BOTTOM EXTENSION RAIL BETWEEN STRAPS		10. ALIGN TOP EXTENSION RAIL BETWEEN STRAPS		11. INSTALL REMAINING TWO STRAP BOLTS
INSTALL STRAPS ON BOTH
SIDES OF I-RAIL		FIT BOTTOM RAIL SECTION			INSTALL THE LAST TWO BOLTS
INSTALL BOLT AND	BOTTOM RAIL SECTION		TOP RAIL SECTION
					AND NUTS THROUGH THE
		BETWEEN THE TWO
NUT IN FIRST SLOT					REINFORCING STRAP SLOTS
		REINFORCING STRAPS		RAIL EDGES
				MUST LINE UP
				STOCK
				I-RAIL
USE 1/4-20 x 13/16" BOLTS		STOCK I-RAIL
AND KEPS NUTS SUPPLIED	BE SURE ALL THE
	SLOTS ARE ALIGNED
INSTALL BOLT AND NUT			FIT THE TOP RAIL SECTION
	RAIL EDGES MUST LINE UP		BETWEEN THE STRAP ON
IN THE SECOND SLOT				BE SURE ALL THE
			THIS SIDE AND THE BOTTOM
	FOR SMOOTH TROLLEY			SLOTS ARE ALIGNED
			RAIL SECTION
	OPERATION				USE 1/4-20 x 13/16" BOLTS
		NOTCH ON THE BOTTOM RAIL			AND KEPS NUTS SUPPLIED
		WILL BE ON THIS END, BUTTING
		UP TO THE NOTCH ON THE STOCK I-RAIL