Vision Fitness R2700HRT E P 4 Green BAG, E P 1 Orange BAG, E P 5 Black BAG, E P 6 Yellow BAG

A s s e m b l y G u i d e

R2700HRT

COMMERCIAL FITNESS BIKE

Accessor y

Tray

Pedal

Plastic Seat	Lumbar Controlled
Cover	Seat Back
	Seat Bottom

S T E P 3 PINK BAG

• Mount the upper handlebars to the
console mast using two lock washers
(M8) and two bolts (M8x15L). Tighten
with the 5mm T-shaped wrench.
• Remove the four mounting bolts from
the back of the console. Connect the
wire harness and heart rate wires that
run through the console mast into the
plugs located in the back of the console.
Attach the console to the mast with the
four bolts removed earlier.
• Remove the battery cover on	the
backside of the console. Plug in	the

To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here:

Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike.

If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12

NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before completely tightening any ONE bolt or screw.

S T E P 6

S T E P 5

9-volt battery. Re-attach the battery cover.

S T E P 4 GREEN BAG

•Attach the seat frame to the sliding seat bracket using four lock washers (M8) and four socket head bolts (M8x20L) and the 6mm T-shaped wrench.

•Connect Wires A on the seat handlebar to Wires B on the sliding seat bracket. Attach the seat handlebars to the sliding seat bracket using four lock washers (M8) and four bolts (M8x15L). Tighten with the 5mm T-shaped wrench.

S T E P 1 ORANGE BAG

•Install the rear foot with the four lock washers (M8), two inside bolts (M8x65L), and two outside bolts (M8x20L). Tighten with the 5mm T-shaped wrench.

S T E P 2 BLUE BAG

•Slide the console mast boot onto the console mast.

•Unfold the wire harness and heart rate wires located in the console mast frame bracket. Attach the wire tie coming from the bottom of the console mast to the wire harness and heart rate wires. Pull the wire tie with wire harness and heart rate wires up through the top of the console mast while simultaneously sliding the mast into the frame bracket.

•Secure the console mast to the frame bracket with six lock washers (M8) and six bolts (M8x15L). Tighten with the 5mm T-shaped wrench. Place the seventh bolt (M8x15L) in the rear of the frame bracket and tighten until snug.

•Slide the console mast boot down and snap it into place on the side cover.

S T E P 1

Rear Foot

Console Mast

Console Mast

Boot

Seat Handlebar

Wires A

Seat Frame

S T E P 4

Console Mast

Handlebar

S T E P 5 BLACK BAG

• Secure the Lumbar controlled seat back and the seat bottom to the seat frame with eight lock washers (M6) and eight bolts (M6x55L). Tighten with the 4mm L-shaped wrench.

• Snap the plastic seat cover into place on the back of the lumbar controlled seat.

S T E P 3

S T E P 6 YELLOW BAG

• Attach the left and right pedals to the left and right crank arms. Tighten the pedals using the 15mm pedal wrench.

• Secure the accessory tray to the seat handlebar with two bolts (M5x35L) and two lock washers (M5). Tighten with the screwdriver.

S T E P 2

Frame Bracket

Wires B

Sliding Seat

Bracket