ENG
Design Pat. Pending Copyright©2005 CATEYE Co., Ltd.
INTRODUCTION
Before using the light, please thoroughly read this manual and keep it for future reference.
Thank you for purchasing the CATEYE TRIPLE SHOT
COMPONENTS
| H31 for oversized H32 | Cable Straps (x 2) |
| handlebars |
|
| Bracket (with thick and thin |
|
Light Unit/Switch Unit Battery Unit/Battery Bag Battery Charger | rubber pads for each) | Support Strap |
|
Connecting and Securing Cables
1.Align the male and female cable ends and connect them. Turn the plugs so that they are securely locked. Fix the cables to your frame and/or stem to keep them secured.
CAUTION!: Pay attention to the arrangement of the cable so that it does not interfere with the handling of the bicycle. Do not secure the cable at an acute angle because the wire inside the cable may break.
Cable
To Light Unit/Switch
Unit
| Line |
| To Battery Unit |
Lock | To Battery Unit |
|
Frame or
Stem
Cable
Straps
Cable Straps
FOR SAFE OPERATION
•Never
•Securely connect the plug so that the cable will not come unplugged or hinder your riding.
•Never use damaged components (e.g., cables, etc.). Send any damaged components to our customer service department for repair.
•The light unit may become extremely hot when on or immediately after it is turned off. Please use with caution.
•Do not place it within children’s reach.
•We recommend carrying a flashlight or spare battery unit with you in case the main battery dies.
•Charge the battery unit before using because the unit
•Do not leave the battery overly discharged because it shortens the operating life of the battery. Try to charge the battery unit after each use. (“Overly discharged” refers to the state the battery is in when used over a period of time while below the specified cutoff voltage.)
•If the lamp body or parts become dirty with mud, etc., clean with a soft cloth which is moistened with mild soap. Never apply paint thinner, benzine or alcohol; damage will result.
•Place the battery unit at least 10 cm away from any wireless meter, as transmitting and receiving perfor- mance may be adversely affected.
•Never disassemble the light unit, battery unit, or battery charger.
•This product is
Before Initial Use
The battery is shipped with a small charge, that is used to test the unit at the factory. As such, it is necessary to charge the battery before initial use. (Refer to the “How to Charge” section in this manual.)
HOW TO MOUNT
HOW TO USE
Switching on/off |
| How to Adjust Beam Angle | ||||||||
To switch the light on/off, press the button on the switch |
| Adjust the beam angle downward so as not to blind oncoming traffic. | ||||||||
unit. |
|
|
|
|
| It can also be adjusted 10 degrees to the left and right. | ||||
Run time | Approx. 3.3 | hours |
|
|
|
|
|
|
| |
|
|
| Beam Adjustment |
| ||||||
Switch Unit |
|
| Button |
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |||
Bracket |
Loosen the lever |
Quick lever
How to Charge Battery Unit
| Important! | Charging indicator state | |
• | Be sure to use only the supplied battery charger. This charger | Orange Light | : Connected to power source |
| can accept | Blinking Red Light : Charging | |
• | Do not completely remove the battery unit from the battery bag. | Green Light | : Charging is completed |
• | After charging, return the battery to its original storage state. Do not allow water to enter the battery bag. |
• | The standard charging time and run time are guideline values and depend on the operating environment. |
• | If the battery unit repeatedly does not meet the proper run time even though it is fully charged, it might be |
| at the end of its operating life. Replace the old battery unit with a new one. The used battery unit should be |
| disposed of properly according to local regulations. |
Installing Bracket
Attach bracket H31 or H32 to the handlebar.
NOTE: Select H31 for oversized handlebars.
1. | Mount a rubber pad and the bracket onto the handlebar. 2 |
| thicknesses of rubber pads are supplied; if necessary, cut |
| the rubber pad to fit. |
2. Tighten and then close the lever to secure it. Make sure the | |
Bracket
Rubber pad
1. | Remove the battery bag from your bicycle and open the bag. |
2. Connect the jack to the battery charger. | |
3. | Plug the battery charger to an AC outlet. |
| NOTE: When charging is complete, the indicator light changes from flashing red to green. |
4. When charging is complete, unplug the charging adapter. Refer to the figures below to rearrange the cable and use the seal | |
| strap to tightly close the opening. |
CAUTION!: When securing the battery to the frame, make sure the fixing strap attaches to the center of the battery unit.
bracket does not rotate on the handlebar. |
CAUTION!: Be sure to adjust the angle of the light’s beam by referring to the “How to Adjust Beam Angle” section in this manual before operat- ing the lighting system.
Mounting Light Unit/Switch Unit
Mounting Light Unit
Mount the light unit onto the bracket.
To remove unit after use, pull it out while pressing the button on the bracket.
Quick lever 
(For H32 only)
Handlebar 
or
Light Unit 
Button
Slide in
Charging Indicator | To AC Power Outlet |
| |
| Battery Charger |
| Battery Unit |
Standard charging time
Approx. 3 hours Charging jack
After Charging | Cable Arrangement |
|
| Charging jack |
Seal Strap | Plug |
|
Fixing Strap
CAUTION!: Make sure the light unit is cool to the touch before removing it.
How to Store Battery Unit | Battery Unit |
Mounting Switch Unit | Switch Unit | Strap |
Mount the switch unit onto the handlebar.
CAUTION!: Mount the switch unit where it does not interfere with the handling of the bicycle. Make sure that it is securely mounted.
1. Adjust the length of the strap with the toggle and wrap the 
strap under the bar, hooking it on the switch unit. Make sure
the switch unit does not move around easily.
Adjuster
Handlebar
The battery unit is stored in its bag as shown in the fig- ure. In case the battery unit is out of its bag, be sure to return it to its original state. Otherwise, rainwater may enter the bag, leading to problems with the unit.
Seam
SPARE PARTS
The following spare parts are available.
CAUTION!: Use only genuine spare parts from CATEYE.
Installing Battery Unit
Install the battery unit. If the battery unit has been taken out of the battery bag, refer to the “How to Charge Battery Unit” section in this manual and check for the correct arrangement of the cable and its storage state.
CAUTION!: When mounting the unit, make sure that the seam of the battery bag is facing down and the fold line is in front. Wind the fixing strap around the center of the battery unit.
Fold Line | Seam |
| Top Tube |
UL : | |||||
|
|
|
|
| |
|
|
| UK : |
|
|
|
|
| EC : |
|
|
|
|
| AS : |
|
|
Light Unit/ | Battery Unit/ | Battery Bag Set | Battery Charger | Bracket H31 | H32 |
Switch Unit | Battery Bag |
|
|
|
|
SPECIFICATIONS |
| LIMITED WARRANTY |
|
| |
1.Wrap the fixing strap around the top tube to secure the unit.
CAUTION!: Wrap the strap over the top tube but under the gear and brake cables. Wrapping the strap over the cables is dangerous as it may inter- fere with braking and gear shifting.
2.Use the support strap to secure the battery unit to the down tube to prevent it from rolling.
NOTE: The battery can also be mounted on alternate positions on the bicycle. However, please make sure that the seam of the battery bag is facing down, and the fold line is in front. This will help prevent any water from entering the bag.
| Gear & Brake |
| Cables |
Fixing Strap | Battery Unit/Battery Bag |
| |
Down Tube | Fixing Strap |
| |
Support Strap |
|
Light Source | Three |
| LEDs |
Battery Unit | Nickel hydride battery |
| |
Battery Charger | |
| 50/60Hz 0.5A) |
Operating Time | Approx. 3.3 hours |
Standard charging time - Approx. 3 hours | |
Temperature range | Charging: |
Operating:
Recharge/discharge number of times
About 300 times (until the rated capacity drops to 50%)
*The specifications and design are subject to change without notice.
If trouble or damage occurs during normal use, the product will be repaired or replaced free of charge. Type your name, address, date of purchase and the situation of trouble clearly on the warranty certificate, and send it back to the appropriate service center together with the product. Insurance, handling and transportation charges shall be borne by the customer. After being repaired or replaced, the product will be shipped back to the customer.
| CO.,LTD. | Service & Research Address for USA | |
CATEYE Service and Research Center | |||
Osaka | 1705 14th St. 115 Boulder, CO 80302 | ||
Attn: CATEYE Customer Service Section | Phone | : 303.443.4595 | |
Phone | : | Toll Free : 800.5CATEYE | |
Fax | : | Fax | : 303.473.0006 |
: support@cateye.co.jp | |||
URL | : http://www.cateye.co.jp | URL: http://www.cateye.com | |