CATEYE SINGLE SHOT PLUS | ENG |
| |
Pat. and Design Pat. Pending | |
Copyright© 2007 CATEYE Co., Ltd. | |
1 | |
INTRODUCTION
Before using the light, please read this manual and the attached “NiMh Batteries” thoroughly, and keep them for future reference.
Thank you very much for purchasing the CATEYE "SINGLE SHOT PLUS
FOR SAFE OPERATION
•Do not place it within children's reach.
•In preparation for unexpected battery shutoff, we recommend you carry a
•If the light unit or parts become dirty with mud, etc., clean with a soft cloth which is moistened with mild soap. Never apply paint thinner, benzine or alcohol; damage will result.
•Mount the light unit more than 10 cm away from the wireless meter. When it is mounted too close, the transmission may be affected adversely.
•This product has waterproof features that allow you to use it in rain. Do not use it soaked in water.
Before Initial Use
HOW TO USE
1 Lighting (lighting pattern selection) | Switch | |||
The lighting pattern is selected using a switch. |
| |||
|
|
|
| |
| Switch | Standard continu- |
| |
| ous lighting time |
| ||
|
|
| ||
ON ↔ OFF : Long press | Hi | : About 3 hours |
| |
Hi ↔ Low | : Single press | Low | : About 9 hours |
|
Flash | : Quick double press | Flash : About 36 hours |
| |
|
| Double press |
ON | Hi |
|
2 sec. |
| x1 |
|
| Flash |
OFF | Low | Double press |
| ||
2 Remaining battery capacity | Battery indicator | |
When the battery indicator lights up red, the bat- tery is almost shutoff. Charge the battery as soon as possible.
Before shipment, it is charged enough to check the light. Be sure to charge it before use, according to the instructions "How to charge."
COMPONENTS
| Battery charger |
Light unit | H34 Bracket |
3How to charge
1�Open the charge jack cover at the back of the light unit to connect the battery charger plug.
2�Plug the battery charger to an AC outlet.
3�After charging, remove the plug and close the charge jack cover.
1
Charge jack
Charging Indicator
Battery charger
2
HOW TO MOUNT
1�Wrap the bracket strap around the handlebar, and put it in the dial.
2�Securely tighten the strap by turn- ing the dial.
Bracket
Bracket rubber pad |
2 |
*Be sure to use the special purpose battery charger.
*Charging and lighting times are approximate values, and will vary by environmental and user conditions.
To AC power outlet
Charging indicator state | Standard charg- | ||
ing time | |||
|
| ||
Blinking red light : Charging | Approx. 4 hours | ||
Green light | : Charging is completed | ||
| |||
3�Cut off the excess bracket strap extending from the dial.
4�I n s e r t t h e l i g h t u n i t t o the bracket until it clicks . To remove, pull out while pressing the release button.
CAUTION!:
•Make sure to tighten the dial by hand. If you tighten it too hard with a tool, the screw threads may be stripped.
•When the angle adjustment on the right and left sides is loose, tighten the screw (*1).
•Round off the cut edge of the bracket strap to prevent injury.
How to Adjust Beam Angle
5�Slightly loosen the dial on the bracket.
6�Adjust the light unit angle so that the light is not directed to oncom- ing cars.
*When the dial is too firm to loosen, wash it slightly with water to loosen it.
*Do not loosen the dial too much, or the bracket strap may come off. Loosen the dial just enough to allow the bracket to move slightly. Securely tighten the dial after adjusting the strap.
*It can also be adjusted 10 degrees to the left and right.
| 3 |
Dial | Bracket strap |
| |
| *1 |
Screw
Light unit
4 | Release button |
6 
HOW TO REPLACE BATTERY
1�Turn over the light, and remove the 2 screws at the front of the lens using a 2.5 mm Allen wrench.
2�Slowly pull out the lens unit from the body.
3�Remove the battery connector con- nected to the board, and replace it with a new battery.
4�Place the battery on the tray, and insert it to the body in place, and secure it with 2 screws.
CAUTION!:
•The lens unit is a precision part; therefore, never disassemble it. Otherwise, the optimum light distribution may be lost.
•To maintain its waterproof features, assemble the lens unit with a rubber
•In order to avoid cable damage, when
1 |
|
| Body |
Lens unit |
|
| Battery |
2 | Screw |
|
Rubber packing
3
Battery connector
Back side of lens
Rubber packing
OK 
NO!
SPARE PARTS
H34 Bracket
NiMH 4.8v 2700mAH
SPECIFICATIONS
Light source | High power white LED x 2 | |
Battery | NiMH 4.8v 2700mAH | |
Battery charger | ||
Operating time | Hi : Approx. | 3 hours |
| Low : Approx. | 9 hours |
| Flash : Approx. | 36 hours |
Standard charging time |
| |
| Approx. 4 hours | |
Temperature range | Charging : 32˚F – 104˚F (0˚C – 40˚C) | |
| Operating : 5˚F – 113˚F | |
Recharge/discharge number of times | ||
| About 300 times (until the rated capacity drops to | |
| 50%) |
|
Dimensions/weight | ||
8.92oz (253 g)
*The specifications and design are subject to change without notice.
LIMITED WARRANTY
CatEye products are warranted to be free of defects from materials and workmanship for a period of 2 years from original purchase. If the product fails to work due to normal use, CatEye will repair or replace the defect at no charge. Service must be performed by CatEye or an authorized retailer. To return the product, pack it carefully and enclose the warranty certificate (proof or purchase) with instruction for repair. Please write or type your name and address clearly on the warranty certificate. Insurance, handling and transportation charges to CatEye shall be borne by person desiring service.
For UK and REPUBLIC OF IRELAND consumers, please return to the place of purchase. This does not affect your statutory rights.
CO.,LTD.
Attn : CATEYE Customer Service Section Phone :
Service & Research Address for USA
CATEYE Service and Research Center 1705 14th St. 115 Boulder, CO 80302
Phone : 303.443.4595 Toll Free : 800.5CATEYE Fax : 303.473.0006