Required Tools, General Notes | Star Trac IP-S1315 specs

INSTALLATION INSTRUCTIONS

REQUIRED TOOLS:

• 2.5MM HEX KEY SOCKET • • • • • • • • • • • • • • • • • • •• • • • • • • • • • • •	1	• 13MM OPEN-END WRENCH • • • • • • • • • • • • • • • • • • •• • • • • • • • •	2
• 3MM HEX KEY SOCKET • • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •	1	• 17MM OPEN-END WRENCH • • • • • • • • • • • • • • • • • • •• • • • • • • • • •	1
• 4MM HEX KEY SOCKET • • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •	1	• 19MM OPEN-END WRENCH • • • • • • • • • • • • • • • • • • •• • • • • • • • • •	1
• 5MM HEX KEY SOCKET • • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •	1	• 13MM SOCKET • • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •• • • • • • • • • • • •	1
• 6MM HEX KEY SOCKET • • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •	1	• #2 CROSS-HEAD (PHILLIPS) SCREWDRIVER • • • • • • • • •	1
• 8MM HEX KEY SOCKET • • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •	1	• TORQUE WRENCH • • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • •• • • • • • •	1

GENERAL NOTES:

•Unless otherwise noted Loctite 242/243 or equivalent thread locker must be used on all threaded fasteners. (Do not use thread locker when a Nyloc nut is used.)

•All Star Trac Strength equipment MUST be secured to the floor using either 10mm or 3/8in. (grade 5 minimum) bolts. To accommodate this there are four mounting points inside the weight stack and one in either of the small feet.

•This Installation Instructions Manual must be used in conjunction with the equipment’s Owner’s Manual. The Owner’s manual describes equipment setup and instructs members on how to use it correctly and safely.

•The Leg Curl Machine weighs approximately 297 Kg (655 lbs) when fully assembled and occupies an area 121 cm wide by 131 cm deep. Star Trac recommends the addition of 1-2 people during assembly, and when moving the equipment to its designated point of use.

THREAD LOCKER APPLICATION: Clean all threads and holes, apply no more than 3-4 drops per bolt.

Thru HolesBlind Holes

Metric Steel Bolts Torque Specifications

	Bolt Size	Thread Pitch	Torque, N-m (lbs-ft)

	6mm	1.25	4.5 to 6 (6 to 8)

	8mm	1.25	9.5 to 12 (13 to 16)

	10mm	1.75	26 to 30 (35 to 40)

•	Torque all hardware to values as specified above, unless noted otherwise.
•	See Page 13 of this manual for fastener sizing information; for reference only.
•	Note: All torque values are in N-m unless otherwise stated.

Should any component not be present or if you have any operational questions, please refer to your owner’s manual or on the web @ www.startrac.com . Specifically refer to your Inspiration serial number and model number labeled on your equipment.

PACKAGING REMOVAL:

Carefully remove all packaging materials that wrap the equipment. DO NOT USE A KNIFE OR BOX CUTTER AS YOU MAY DAMAGE THE EQUIPMENT. At this time remove any sub-components from the pallet and set aside for later assembly.

Page 3