Image IMTL49105.2 user manual

Page 7

2.Orient the Right Upright (36) so the square hole near the lower end is in the position shown. Attach the Right Upright to the Upright Base (48) with two Upright Bolts (40) and two Upright Star Washers (39). Do not tighten the Upright Bolts yet.

Attach each Wheel (45) to the Upright Base (48) with a Wheel Bolt (89), two Wheel Spacers (44), and a Nut (47) as shown. Do not overtighten the Wheel Bolts; the Wheels should turn freely.

3.Cut the tie securing the Wire Harness (28) in a bundle. Do not remove the large colored tie on the end of the Wire Harness.

Orient the Upright Base (48) so the Wheels (45) are at the bottom. Next, position the Upright Base and the Uprights (31, 36) around the frame assembly as shown.

Have another person lift the front of the frame assembly and hold it. Insert the Wire Harness (28) into the square hole near the lower end of the Right Upright (36) and out of the top. Next, raise the Uprights (31, 36) so the Upright Base (48) is flat on the floor. Make sure that the end of the Wire Harness does not fall into the Right Upright; it may be helpful to hold the colored tie on the end of the Wire Harness.

4.Open the included grease packet, and apply equal amounts of grease to both sides of each Frame Spacer (34).

Hold one of the Frame Spacers (34) between the frame assembly and the Right Upright (36); make sure that the Frame Spacer is oriented as shown in the inset drawing. Insert a Frame Bolt (32) through a Frame Washer (33), the Right Upright, the Frame Spacer, and the bracket on the frame assembly. Be careful not to pinch the Wire Harness (28) in the Right Upright. Tighten a Nut (47) several turns onto the Frame Bolt, but do not fully tighten the Nut yet.

Repeat this step on the left side. Note: There is not a wire harness on the left side.

Remove the colored tie from the Wire Harness (28).

2

44

 

89

44

47

45

45

36

44

 

47

 

89

 

 

Square Hole

 

39

 

48

 

 

 

 

 

40

3

 

 

 

 

 

Hole

 

 

31

 

48

 

 

 

28

 

36

 

 

 

 

45

 

 

Frame Assembly

 

 

Colored Tie

 

 

 

28

 

 

4

Colored Tie

 

Left

 

28

 

Side

 

 

 

 

 

34

Right

 

34

 

 

 

Side

 

 

 

 

36

 

 

 

47

 

 

 

33

32

 

 

34

 

 

 

 

59

Frame Assembly

7

Image 7
Contents Mon.-Fri., 6 a.m.-6 p.m. MST QUESTIONS?Model No. IMTL49105.2 Serial No Call TOLL-FREETable of Contents Important Precautions Page Back Right Side Before YOU BeginMake sure that the power cord is unplugged AssemblyPage Make sure that the Wire Harness 28 is not pinched Top View Frame BoltsPage MyTracks StepCounter Console DiagramFeatures of the Console HOW to Turn on the PowerHOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt HOW to USE the Manual Mode Whenkey. you are finished exercising, remove HOW to USE the Mytracks Stepcounter ProgramMeasure your heart rate if desired Turn on the workout fan if desiredHOW to USE a Trainer Program When the program is completed, remove Key from the consoleSelect a trainer program Information MODE/DEMO Mode HOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked onExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Page Key No. Qty Description Part LIST-Model No. IMTL49105.2R0506A Limited Warranty HOW to Order Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT