Image IMTL39520 user manual Troubleshooting, Problem The power turns off during use

Page 22

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll- free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 9). Use only a single-outlet surge suppressor that meets all of the specifications described on page 9. Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c. Check the circuit breaker located on the treadmill

c

 

near the power cord. If the switch protrudes as

 

 

 

shown, the circuit breaker has tripped. To reset the

Tripped

Reset

circuit breaker, wait for five minutes and then press

 

 

the switch back in.

 

 

PROBLEM: The power turns off during use

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the

circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c. Remove the key from the console. Reinsert the key fully into the console.

d. If the treadmill still will not run, please call our toll-free Customer Service Department.

PROBLEM: The speed display on the console does not function properly

SOLUTION: a. Remove the key and UNPLUG THE POWER CORD. Remove the hood from the treadmill. Locate the Reed Switch (21) and the Magnet (43) on the left side of the Pulley (42). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap be- tween the Magnet and the Reed Switch is about 1/8”. If necessary, loosen the 3/4” Screw (76) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

1/8”

42

76

 

21

43

 

Top

 

View

 

22

Image 22
Contents Model No. IMTL39520 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Page Right Side Before YOU BeginLeft Side Assembly Make sure that the power cord is not pluggedRectangular Hole Bend 107 Ground Wire 108 118 HOW to Plug in the Power Cord Operation and AdjustmentPerformant Lubetm Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeHOW to USE Personal Trainer Programs When the program is completed, remove Key from the console Follow your progress with the displaysHOW to Connect Your Portable Stereo HOW to Connect Your Home Stereo HOW to Connect Your Computer HOW to Connect Your VCR Adapter Audio CablePressVCR. the Play button on your CD player or Insert the key into the consoleWhenkey. the program is completed, remove Return to the treadmill and stand on the foot HOW to USE Programs Directly from OUR WEB SiteFollow the on-line instructions to start Program Follow your progress with the LED track DisplaysInformation Mode HOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Workout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Page R0203A Key Qty DescriptionExploded IMTL39520 Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT