NordicTrack NTTL18901 Follow your progress with the displays, Measure your heart rate if desired

Page 13
Current Segment

When you select a preset program, the left side of the main display will flash the maximum incline setting of the program and the right side of the display will flash the maximum speed setting of the program for ten seconds. Three seconds after a preset program is selected, the name of the se- lected program and the total program time will begin to scroll across the main display.

The program dis- play will show the first thirteen speed settings for the program you have selected.

3 Press the Start Program button or the Speed + button to start the program.

A moment after the button is pressed, the tread- mill will automatically adjust to the first speed and incline settings for the program. Hold the handrails and begin walking.

Each program is divided into several time seg- ments of different lengths. The main display shows both the time remaining in the program and the time remaining in the current segment of the pro- gram. One speed setting and one incline setting are programmed for each segment. The speed setting for the first

segment is shown

in the flashing Current Segment column of the pro- gram display. (The incline set- tings are not

shown in the program display.) The speed set- tings for the next thirteen segments will be shown in the thirteen columns to the right.

When only three seconds remain in the first seg- ment of the program, both the Current Segment column and the column to the right will flash, a se- ries of tones will sound, and all speed settings will move one column to the left. The speed setting for the second segment will then be shown in the flashing Current Segment column and the tread- mill will automatically adjust to the speed and in- cline settings for the second segment.

The program will continue in this way until the speed setting for the last segment is shown in the Current Segment column and no time remains in the program. The walking belt will then slow to a stop.

Note: Each time a segment ends and the speed settings move to the left, if all of the indicators in the Current Segment column are lit, the speed set- tings may move downward so that only the highest indicators in the columns will appear in the pro- gram display. When the speed settings move to the left again and not all of the indicators in the Current Segment column are lit, the speed settings will move back up.

If the speed or incline setting for the current segment is too high or too low, you can manually override the setting by pressing the Speed or Incline buttons on the console. Every few times one of the Speed buttons is pressed, an additional indicator will light or darken in the Current Segment column. If any of the columns to the right of the Current Segment column have the same number of lit indicators as the Current Segment column, an additional indicator may light or darken in those columns as well. Note: If you manually adjust the speed setting so that all of the indicators in the Current Segment column are lit, the speed settings in the program display will not move downward as described above. Note: If you manually override the speed or incline setting for the current seg- ment, when the segment ends the treadmill will automatically adjust to the speed and incline settings for the next segment.

To stop the program temporarily, press the Stop button. The time will begin to flash in the main dis- play. To restart the program, press the Start Program button or the Speed + button. To end the program, press the Stop button, remove the key, and then reinsert the key.

4 Follow your progress with the displays.

See step 5 on page 11.

5 Measure your heart rate if desired.

See step 6 on page 12.

6 When the program has ended, remove the key.

Step onto the foot rails and make sure that the in- cline of the treadmill is at the lowest level. Next, remove the key from the console and put it in a se- cure place. Note: If the displays and indicators on the console remain lit after the key is re- moved, the console is in the “demo” mode. Refer to page 24 and turn off the demo mode.

When you are finished using the treadmill, move the on/off switch near the power cord to the off position and unplug the power cord.

13

Image 13
Contents Model No. NTTL18901 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Page Left Side Before YOU BeginRight Side Assembly Bolts yet HOW to Plug in the Power Cord Operation and AdjustmentPerformant Lubetm Walking Belt Features of the Console Getting Started Select the manual mode HOW to USE the Manual ModeChange the incline of the treadmill as desired Training Zone disSelect the desired preset program HOW to USE Preset ProgramsSpeed/Pace-The right side of the main Measure your heart rate, if desiredFollow your progress with the displays When the program has ended, remove the keyMeasure your heart rate if desired Select one of the custom programs HOW to Create Custom ProgramsRemove the key HOW to USE Custom Programs Put on the chest pulse sensor HOW to USE the Fitness Test ProgramSelect the fitness test program Enter your ageSelect the pulse-driven program HOW to USE the PULSE-DRIVEN ProgramRefer to on HOW to Connect Your Portable Stereo HOW to Connect Your Computer HOW to Connect Your Home StereoAudio Adapter Cable HOW to Connect Your VCRPressVCR. the Play button on your CD player or Whenkey. the program is completed, remove Follow the on-line instructions to start the program HOW to USE Programs Directly from OUR Internet SiteOptional Chest Pulse Sensor Information MODE/DEMO ModeHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USEProblem The power turns off during use TROUBLE-SHOOTINGTop Problem The walking belt slows when walked on Exercise Intensity Conditioning GuidelinesWorkout Guidelines Suggested Stretches Description Qty R0401AQty Description Ordering Replacement PartsNTTL18901 Exploded Limited Warranty