4.Slide the Grounding Bracket (107) onto one of the Handrail Spacers (65) in the location shown.
See inset drawing A. Pinch the tabs on the Grounding Bracket (107) so that the tabs will fit into the hole in the Upright (69 [see inset drawing B]).
See inset drawing B. Place the Handrail Spacer (65) on the left Upright (69) as shown, with the cutout on the indi- cated side. Note: Make sure that the tabs on the Grounding Bracket (107 [see inset drawing B]) are in- serted into the hole in the Upright.
5.Pull the Upright Wire Harness (98) up through the other Handrail Spacer (65). Place the Handrail Spacer on the right Upright (69) as shown, with the cutout turned toward the treadmill (see inset drawing A).
Have a second person hold the Handrails (66) near the Uprights (69) as shown. Connect the Upright Wire Harness (98) to the wires extending from the Console Base (81). Insert the connectors and the Upright Wire Harness into the hole in the Console Base (see inset drawing B).
Set the Handrails (66) on the Handrail Spacers (65), being careful not to pinch the Upright Wire Harness (98).
6.Insert two Handrail Bolts (78) with Handrail Washers
(77)and Handrail Bushings (75) into the right Upright
(69)and the right Handrail Spacer (65). Turn the
Handrail Bushings so they fit against the Upright with the thick sides of the Bushings toward the center of the treadmill as shown in the inset drawing. Lift the right Handrail (66) slightly and align the Bolts with the holes in the Handrail. Next, thread the Bolts into the Handrail.
Do not tighten the Bolts yet.
Attach the left Handrail (not shown) in the same way. Tighten all four Handrail Bolts (78).
4 | 107 | 65 |
| A | Tabs |
|
|
|
|
| |||
|
|
|
| 107 |
|
|
B |
|
|
|
|
|
|
|
|
|
|
| Cutout | |
| 65 |
|
|
|
| 69 |
|
|
|
|
|
| |
5 |
|
|
| A |
|
|
|
| 81 | Cutout |
| ||
|
|
|
|
| ||
|
|
|
| 65 |
|
|
|
|
| 66 |
|
| |
|
|
|
|
|
| 69 |
|
| 98 | 69 | B | 98 |
|
| 65 |
|
|
|
|
|
|
|
|
|
|
| 81 |
6 |
|
|
|
|
|
|
|
|
|
| 66 |
|
|
|
|
|
| 65 |
|
|
|
|
|
| 69 |
|
|
|
|
|
| 75 |
| |
|
|
|
|
| 77 | Thick |
|
|
|
|
| Side | |
|
|
|
|
|
| |
|
| 75 | 77 |
| 78 |
|
|
|
|
|
| ||
7.Make sure that all parts are properly tightened before you use the treadmill. Note: If there is a thin sheet of clear plastic on the hood decal or the “ComforTrack” decal, remove it. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 24). To protect the floor or carpet from damage, place a mat under the treadmill.
7