Healthrider HRTL71706.0 HOW to Fold and Move the Treadmill, HOW to Fold the Treadmill for Storage

Page 17

HOW TO FOLD AND MOVE THE TREADMILL

HOW TO FOLD THE TREADMILL FOR STORAGE

Before folding the treadmill, adjust the incline to the lowest position. If this is not done, the treadmill may be- come permanently damaged. Next, unplug the power cord. CAUTION: You must be able to safely lift 45 pounds (20 kg) to raise, lower, or move the treadmill.

1.Hold the metal frame firmly in the location shown by the arrow at the right. CAUTION: To decrease the possibility of injury, do not lift the frame by the plastic foot rails. To raise the frame, bend your legs, keep your back straight, and lift with your legs. Raise the frame about halfway to the vertical position.

2.Move your right hand to the position shown and hold the treadmill firmly. Using your left hand, pull the latch knob to the left and hold it. Raise the frame until the latch pin is aligned with the gap between the frame and the foot rail. Slowly release the latch knob. Make sure that the latch pin is fully inserted between the frame and the foot rail.

To protect the floor or carpet from damage, place a mat under the treadmill. Keep the treadmill out of direct sun- light. Do not leave the treadmill in the storage position in temperatures above 85° Fahrenheit.

HOW TO MOVE THE TREADMILL

Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the latch pin is fully inserted between the frame and the foot rail.

1.Hold the upper ends of the handrails. Place one foot against one of the wheels.

2.Tilt the treadmill backward until it rolls freely on the front wheels. Carefully move the treadmill to the desired location.

To reduce the risk of injury, use extreme caution while moving the treadmill. Do not move the treadmill over an uneven surface.

3.Place one foot against one of the wheels, and carefully lower the treadmill until it is resting in the storage position.

Frame

Frame

Engaged

Latch Knob

 

Latch Pin

 

Handrail

Wheel

17

Image 17
Contents Call TOLL-FREE QUESTIONS?Model No. HRTL71706.0 Serial No Table of Contents Important Precautions Page For your benefit, read this manual carefully before Before YOU BeginRight Side BackShaft at least 6 long and wire cutters AssemblyMake sure that the power cord is unplugged Extension leg. Firmly tighten the Extension Leg BoltsFrame 58 yet Connectors are not Connected Connect the connectors properly seeBe careful to avoid pinching any of the wires Make sure that the ground wire see stepSmall Screws PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerWhenkey. you are finished exercising, remove Measure your heart rate if desiredTurn on the fan if desired Select one of the six cross trainer programs HOW to USE a Cross Trainer ProgramContinue the cross trainer program Perform the first strength exercise when PromptedOptional Chest Pulse Sensor Information MODE/DEMO ModeHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Top View Exercise Intensity Conditioning GuidelinesWorkout Guidelines Exercise FrequencyQty Description R0906AOrdering Replacement Parts Exploded Drawing A-Model No. HRTL71706.0 R0906A Exploded Drawing B-Model No. HRTL71706.0 R0906A Exploded Drawing C-Model No. HRTL71706.0 R0906A Exploded Drawing D-Model No. HRTL71706.0 R0906A Limited Warranty