JVC UX-H33 manual Connecting Other Equipment, Adjusting the Voltage Selector

Page 11

Continued

To remove the speaker grilles

The speaker grilles are removable.

Projections

Holes

Speaker grille

To remove the speaker grille, insert your fingers at the top of the speaker grille, pull towards you. Then pull the bottom towards you.

To attach the speaker grille, follow the illustration

above.

Connecting Other Equipment

To connect an audio equipment

You can connect audio equipment—used only as a playback device.

•DO NOT connect any equipment while the power is on.

•DO NOT plug in any equipment until all connections are complete.

Be sure that the plugs of the audio cords are colored: White plugs and jacks are for left audio signals, and red ones for right audio signals.

R

L

L

Audio equipment

To audio output

R

 

For playing other equipment through this unit,

connect between the audio output jacks on the other equipment and AUX jacks by using audio cords (not supplied).

Adjusting the Voltage Selector

Before plugging in the unit, set the correct voltage for your area with the voltage selector on the rear of the unit.

V O L T A G E

S E L E C T O R

2 3 0 V

1 2 7 V

Voltage mark

1 1 0 V

Use a screwdriver to rotate the voltage selector so the voltage number the voltage mark is pointing at is the same as the voltage where you are plugging in the unit. (See the back cover page.)

DO NOT plug in before setting the voltage selector on the rear of the unit and all connection procedures are complete.

NOW you are ready to plug in the unit and any other connected equipment.

IMPORTANT: Be sure to check all connections to

be done before plugging the power cord.

This unit can be supplied with power through the AC IN connector (at home) or the DC IN connector (in a car).

•Do not connect the unit using the AC IN connector and the DC IN connector at the same time for safe and correct use.

To connect the AC power cord

 

 

 

AC power cord (supplied)

AC IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connect the AC power cord to the AC IN connector and a wall outlet.

•If the wall outlet does not match the AC plug, use the supplied AC plug adaptor.

8

English

Page 10 Page 12
Image 11
Page 10 Page 12
Contents UX-H30- Consists of CA-UXH30 and SP-UXH30 UX-H35- Consists of CA-UXH35 and SP-UXH35UX-H33- Consists of CA-UXH33 and SP-UXH33 Page Important for Laser Products About This Manual PrecautionsIntroduction Contents Front view Location of the ButtonsMain Unit Top viewMain unit Display windowRemote Control To connect an outdoor FM antenna Supplied AccessoriesConnecting Antennas Getting StartedTo connect an outdoor AM antenna Connecting SpeakersTurn the AM loop antenna until you have the best reception Release your finger from the clampTo remove the speaker grilles Connecting Other EquipmentAdjusting the Voltage Selector To connect the AC power cordWhen using the unit in your car Putting the Batteries into the Remote ControlCommon Operations Setting the ClockSetting the AM Tuner Interval Spacing Level Adjusting the VolumeAdjusting the Tone Bass/Treble Reinforcing the Bass SoundListening to FM and AM Broadcasts Tuning in to a StationPresetting Stations Press SET again Tuning in to a Preset StationTune in to the station you want to preset Press SETGeneral notes When playing a CD-R or CD-RWPlaying Back Discs Press 0 Open on the unitProgramming the Playing Order of the Tracks-Program Play Basic Disc OperationsPress Random To check the program contentsPlaying at Random-Random Play Repeating Tracks-Repeat PlayPut a cassette in with the exposed part of the tape down Playing Back TapesPlaying Back a Tape Press for cassette deck on the unitTo protect your recording To record on both sides-Reverse ModeRecording Recording on a TapeRepeat steps 2 and 3 to record other tracks you want Disc Direct RecordingOne Track Recording Press ONE TouchSet the off-time when you want the unit To turn off standby Using the TimersUsing Daily Timer and Recording Timer Set the on-time when you want the unit To turn onWith the source to play Adjust the clock if you needSelect the volume level To deactivate the timer temporarilyPress Sleep Using Snooze TimerUsing Sleep Timer How the Sleep Timer actually worksHandling discs MaintenanceCleaning the unit Handling cassette tapesTroubleshooting L T a G E S E L E C T O R
Top Page Image Contents