PART | R0102A |
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.
Key No. | Qty. | Description | Key No. | Qty. | Description |
1 | 2 | Foot Rail Insert | 52 | 1 | Walking Platform |
2 | 2 | Foot Rail | 53 | 6 | Platform Screw |
3 | 2 | Foot Rail Cap Screw | 54 | 2 | Rear Platform Screw |
4 | 1 | Left Foot Rail Cap | 55 | 2 | Rear Isolator |
5 | 2 | Frame Pivot Bolt | 56 | 2 | Isolator Spacer |
6 | 2 | Frame Pivot Spacer | 57 | 1 | Ground Wire |
7 | 1 | Magnet | 58 | 1 | Rear Endcap |
8 | 1 | Front Roller/Pulley | 59 | 2 | Rear Roller Adj. Bolt |
9 | 4 | Frame Pivot Nut | 60 | 1 | Warning Decal |
10 | 1 | Reed Switch/Sensor Wire | 61 | 1 | Allen Wrench |
11 | 4 | 62 | 1 | Rear Roller | |
12 | 1 | Reed Switch Clip | 63** | 1 | Optional Chest Pulse Strap |
13 | 1 | Lift Frame | 64** | 1 | Optional Chest Pulse Sensor |
14 | 1 | Walking Belt | 65 | 2 | Handrail Spacer |
15* | 1 | Motor Assembly | 66 | 1 | Handrail |
16 | 1 | Motor | 67 | 2 | Endcap Clip |
17 | 1 | Pulley/Flywheel/Fan | 68 | 1 | Lock Knob |
18 | 1 | Motor Belt | 69 | 1 | Upright |
19 | 1 | Motor Pivot Nut | 70 | 1 | Lock Knob Sleeve |
20 | 5 | Motor Tension Nut | 71 | 1 | Spring |
21 | 1 | Motor Tension Bolt | 72 | 1 | Lock Pin Collar |
22 | 1 | Motor Pivot Bolt | 73 | 1 | Pin Clip |
23 | 1 | Hood | 74 | 1 | Lock Pin |
24 | 2 | Incline Motor Bolt | 75 | 4 | Handrail Bushing |
25 | 4 | Plastic | 76 | 2 | Pulse Grip |
26 | 1 | Power Board | 77 | 4 | Handrail Washer |
27 | 7 | Screw | 78 | 4 | Handrail Bolt |
28 | 1 | Choke | 79 | 2 | Upright Endcap |
29 | 1 | Controller | 80* | 1 | Latch Assembly |
30 | 1 | Electronics Plate | 81 | 1 | Console Base |
31 | 1 | Motor Controller Wire | 82 | 1 | Console |
32 | 1 | Front Roller Adj. Bolt | 83 | 4 | Belly Pan Screw |
33 | 6 | 2” Console Screw | 84 | 1 | Key/Clip |
34 | 2 | Roller Washer | 85 | 1 | IFIT.com Wire |
35 | 1 | Lock Knob Spacer | 86 | 1 | Jack |
36 | 1 | Incline Motor | 87 | 4 | Handrail Endcap |
37 | 1 | Incline Motor Stop | 88 | 1 | Console Back |
38 | 1 | Motor Belly Pan | 89 | 1 | Releaseable Tie |
39 | 1 | Audio Wire Nut | 90 | 10 | 1” Console Screw |
40 | 2 | Static Decal | 91 | 2 | Cable Tie Clamp |
41 | 1 | Circuit Breaker | 92 | 5 | 8” Cable Tie |
42 | 1 | Power Cord | 93 | 2 | Lift Pivot Bolt |
43 | 1 | On/Off Switch | 94 | 2 | Wheel Bolt |
44 | 1 | Left Endcap Insert | 95 | 2 | Wheel |
45 | 4 | Belt Guide Screw | 96 | 1 | Right Endcap Insert |
46 | 2 | Belt Guide | 97 | 1 | Grommet |
47 | 4 | Isolator | 98 | 1 | Upright Wire Harness |
48** | 2 | Hand Weight | 99 | 4 | Base Pad |
49 | 16 | Fastener | 100 | 16 | 3/4” Screw |
50 | 1 | Belly Pan | 101 | 1 | Motor Washer |
51 | 1 | Right Foot Rail Cap | 102 | 2 | Extension Leg |
26