ParaBody 093 manual BODYSMiTH Prosystem Assembly Instructions, UPRIGHTS. see DRA~VING

Page 7

093 BODYSMiTH PROSYSTEM ASSEMBLY INSTRUCTIONS

24.To install SECONDARYCABLE(PB2559-1), start by inserting the end of the CABLE,WITHOUTthe WHITE BALL under the FRONT PULLEYin the LOWROWPULLEY HOUSING on the MAIN UPRIGHT. (REMOVE PULLEY FOR EASE OF INSTALLATION)

Push the CABLEunder the FRONTPULLEYand through the HOLEof the 1VLAINUPRIGHTto the PULLEYon the UPRIGHTBRACEof the I~L~_IN UPRIGHT.Pull the CABLEuntil the WHITE

BALL stops against the FRONTPULLEYand the LOWROWPULLEYHOUSING.

Pull the CABLEaround the BRACEPULLEYand up to the SECONDPULLEYon the PULLEY BLOCK SYSTEM. (NOTE: THE CABLE MUST BE ROUTED AROUND THE SECOND PULLEY FROM THE REAR TO THE FRONT)

Pull the CABLEaround the SECONDPULLEYof the PULLEYBLOCKSYSTEM~nd down to the first HOLEabove the larger set of HOLESon the MAINUPRIGHTAttach. the end of the CABLEto the MAINUPRIGHT,using one (I) 3/8 X 2-3/4 IN. BOLT.one (!) 3/8 IN. WASHER,one (I) 3/8 LOCKWASHERand one (1) 3/8 IN. NUT. (SEE DETAIL

See CABLEROUTi~NGDIAGRAM(DETAIL A) for help in completing STEP 24.

25.TIGHTEN ALL LOOSE PULLEY CONNECTIONS MADE TO THIS POINT.

.26. Slide four (4) I X 1~ IN. GRIPSover each end of both the LATBAR, and the LOWROWBAR.(NOTE:

IF A LUBRICANT IS REQUIRED, RUBBING ALCOHOL THOROUGHLYCOAXING INSIDE OF THE GRIP IS THE BEST MATERIALTO USE) (SEE DETAIL AND B)

27.Attach the LAT BARto the PRIMARYCABLE, and the LOWROWBARto the SECONDARY CABLE,by using two (2) 5/16 IN. SNAPHOOK.(SEE DETAILA AND

To adjust the LOWROWBAR. Remove the LOWROWBARfrom the 5/16 IN. SNAPHOOKon the

SECONDARYCABLE,and attach the 24 LINK CHAIN. Attach another 5/16 IN. SNAPHOOKto the LOWROWBA:R and adjust it to the desired CHAINLINK. (SEE DETAILB)

29.Attach two (2) sets of UPRIGHTLABELS(designated #1 to #21)to the inside surface of both ~0~

UPRIGHTS. (SEE DRA~VING)

30; To use the LOWROWFOOTBRACE,slip it over the BASELEGS, and up against 15ae UPKIGHTSof the FRONT UPRIGHTS. (SEE DRAWING)

Image 7
Contents Product Assembly INSTRUCTTON, S~ETS Bolt Length Safetyrails WEIGHTCARP/AGEAdjustablekneesupport Paintedconnector8 IN. NUTS. see Drawing BODYSM~THPROSYSTEiV~ ASSE1V~BLY InstructionsBODYSMITi-I Prosystem Assembly Instructions BODYSI~tTU Prosystem Assembly Instructions Tighten ALL Loose Pulley Connections Made to this Point BODYSMiTH Prosystem Assembly InstructionsUPRIGHTS. see DRA~VING Hooks Front Upright Page Bx 3-~,/~. BOLT2 Lowrowfoot Brace