Life Fitness 93Xe manual 10 a

Page 5

IMPORTANT! Do not discard the ship kit located on top of the pedal levers. All necessary components needed to complete the installation are located in the ship kit.

IMPORTANT! Ne jetez pas le kit placé sur le dessus des leviers de pédale. Il contient tous les éléments nécessaires pour l'installation.

1. Locate the LEFT HANDLEBAR (11). Position the HANDLEBAR near the top of

the LEFT PIVOT ARM (A). Connect the HEART RATE CONNECTOR (B)

leading from the HANDLEBAR to the CONNECTOR (C) extending from the top

of the LEFT PIVOT ARM. Carefully slide the excess HEART RATE CABLE into

the top of the LEFT PIVOT ARM.

Align the mounting holes of the LEFT HANDLEBAR with the mounting holes at

the top of the LEFT PIVOT ARM. Secure them together using three SCREWS

(1).

9

11

 

NOTE: Be careful not to pinch the HEART RATE CABLE when securing the

 

LEFT HANDLEBAR to the LEFT PIVOT ARM.

 

REMARQUE : Faites attention de ne pas coincer le CÂBLE DU MONITEUR

 

DE FRÉQUENCE CARDIAQUE en fixant le GUIDON GAUCHE au BRAS

 

MOBILE GAUCHE.

2.

Locate one LEFT FRONT ROCKER COVER (5) and the LEFT BACK

 

ROCKER COVER (6). Position the LEFT BACK ROCKER COVER over the

 

user side of the ROCKER ARM making sure that it seats fully over the

 

BULLHORN MOUNTING BRACKET (D). Place the FRONT ROCKER COVER

 

over the opposite side of the ROCKER ARM in the same manner. Secure the

 

COVERS using two PHILLIPS PAN HEAD SCREWS (2). Tighten the

 

SCREWS securely. Do not over-tighten the SCREWS.

3.

Locate one FRONT PIVOT ARM COVER (9) and one BACK PIVOT ARM

 

COVER (10). Position the BACK PIVOT ARM COVER over the user side of the

 

ROCKER ARM making sure that it interlocks with the ROCKER COVER. Place

 

the FRONT PIVOT ARM COVER over the opposite side of the PIVOT ARM in

 

the same manner. Secure the COVERS using two PHILLIPS PAN HEAD

 

SCREWS (2). Tighten the SCREWS securely. Do not over-tighten the

 

SCREWS.

4.

Locate the LEFT BULLHORN (13). Secure the BULLHORN to THE

 

BULLHORN MOUNTING BRACKET (D) using two FLAT HEAD SCREWS (1).

 

Tighten the SCREWS securely. Locate and attach the LEFT BULLHORN

 

COVER (15) to the base of the BULLHORN using one SCREW (22). Tighten

 

the SCREW securely. Do not over-tighten the SCREW. Slide the GASKET (E)

 

downward to meet the BULLHORN COVER.

B C

2

1

10 A

5

D

A

E

6

5.

Repeat steps one through four to install the RIGHT ROCKER COVERS (5 &

 

6), PIVOT ARM COVERS (9 & 10), BULLHORN (14) and BULLHORN COVER

 

(16).

 

NOTE: The right PIVOT ARM COVERS are reversed front and back. The

 

SCREWS will be installed from the rear.

 

REMARQUE : Les couvercles du BRAS MOBILE DROIT sont inversés à

 

l'avant et à l'arrière. Les VIS sont insérées de l'arrière.

6.

Unwrap the MAIN WIRE, COAXIAL CABLE and HEART RATE HARNESS

 

leading from the MONOCOLUMN (F). Feed the WIRE HARNESSES through

 

the CONSOLE SUPPORT ASSEMBLY TUBE (G) located at the top and front

 

of the MONOCOLUMN. Locate the CONSOLE SUPPORT ASSEMBLY (7) and

 

position it near the top of the MONOCOLUMN. Feed the WIRE HARNESSES

 

through the CONSOLE SUPPORT ASSEMBLY as shown. Align the bottom

 

mounting holes of the CONSOLE SUPPORT ASSEMBLY with those in the

 

CONSOLE SUPPORT ASSEMBLY TUBE. Secure them together using six

 

SCREWS (1). Tighten the SCREWS securely.

 

NOTE: Be careful not to damage the WIRE HARNESSES when routing it

 

through the CONSOLE SUPPORT ASSEMBLY or when mounting the

 

CONSOLE SUPPORT ASSEMBLY to the CONSOLE SUPPORT ASSEMBLY

 

TUBE.

 

REMARQUE : Faites attention de ne pas coincer les FAISCEAUX DE

 

CÂBLES en les insérant dans le SUPPORT DE LA CONSOLE ou en fixant le

 

SUPPORT DE LA CONSOLE au TUBE DE SUPPORT DE LA CONSOLE.

7.

Locate the ACCESSORY TRAY (17). Slide the ACCESSORY TRAY into the

 

top of the MONOCOLUMN (F) as shown. Be sure the ACCESSORY TRAY is

 

fully seated.

 

NOTE: Be careful not to damage the MAIN WIRE HARNESS when sliding

 

the ACCESSORY TRAY into the MONOCOLUMN.

 

REMARQUE : Faites attention de ne pas endommager le FAISCEAU DE

 

CÂBLES PRINCIPAL en glissant le PLATEAU POUR ACCESSOIRES sur la

 

COLONNE MONOBLOC.

 

Secure the ACCESSORY TRAY to the CONSOLE SUPPORT ASSEMBLY

 

using two SCREWS (3). Tighten the SCREWS securely. Do not over-tighten

 

the SCREWS.

21

2

7

 

 

2

1

83

2 13

1

15 22

1

G

F

4

17

Image 5
Contents 95Xe Total Body Trainer Congratulations Important Safety Instructions Tools Required for Assembly 10 a 19 K N L J Page PRE-OPERATION Checklist