Life Fitness 701 manual FACTOR525 PEC DEC ATT. Assemblyinstructionslevel

FACTOR525 PEC DEC ATT. ASSEMBLYINSTRUCTIONS(LEVEL 2) __

o

o

4o "

'7.

LOOSENthe 3/8 X 4 1N. BOLTthat ~ssembles the two (2) PULLEYS,and two (2) I/2 IN. SPACERS the BASEdirectly behind the FRONTUPRIGHTRemove.the 3/8 IN. LOCKNUT, and the 3/8 IN.

WASHERSlide.. the BOLTout enough to remove the two (2) 1/2 IN. SPACERSReplace. if.it I/2 IN.

SPACERSwith one (I) .~-I~ X I IN. PULLEY,as shown in (VIEWB-B). Slide BOLTback Replace the 3/8 IN. WASHER.,and 3/8 IN. NUT. TIGHTENCONNECTIONSECURELY.

SECURELYassemble one (I) 4-I/2 X 1 IN. PULLEYto the single hole in the BASEdirectly behind the FRONTUPRIGHTas shown in (VIEWB-B) on drawing, using one (I) 3/8 X I-3/4 IN. BOLT,two 3/8 IN. WASHERS,and one (1) 3/8 IN. LOCKNUT.

To assemble the LOOPCABLE,follow the cable routing diagram on drawing, and use the following steps:

Assemble one end of the LOOPCABLEto the LEFT ARMADVANCEand the other cad ofthe LOOP CABLE to the RIGHT ARM ADVANCE(MAKE SURE THAT LOOP CABI3E IS

ROUTED BETWEENTHE AB CRUNCH CABLE AND THE FRONT UPRIGHT) as shown on drawing, using~.wo (2) 318 IN. NUT,four (4) 3/8 IN. WASHERS,and two (2) 3/8 IN.

HEIGItT LOCK NUT. (TIGHTEN THE CONNECTION ENOUGHTO REMOVE'rile

PLAY, YET AL].,OWING THE LOOP TO MOVEFREELY)

¯Drape the CABLEover the both PULLEYSon the CENTERPULLEYBI~.CKET. (THIS

WILL FORM A LOOP IN THE CENTER OF THE CABLE)

¯Position CABLERETAININGCLIPS in a 45 DEGREEposition over the PULLEYSand CABLES,and tighten the two (2) PULLEYconnections SECURELYSEE. DRA'~/ING.

To assemble the LINKCABLE,follow the cable routing diagram on drawing, and use the iblt~wing steps:

®LOOSELYassemble the PULLt:Y BRACKETto the LINK CABLEas shown in (DE'.['AIL E) drawing, using two (2) I/4 IN. WASI-tER,and two (2) 1/4-28 IN. NUTS.(LOCATEPULLEY

BRACKET HALF WAY UP ONTItETItREADSOFTHELINKCABLE"	DO NOT
TIGHTEN NUTS AT TItlS TIME)

,,Slip one (1) 4-1/2 X I IN. PULLEYinto the LOOPofthe LOOPCABLEcreated from routing STEP 3. (VIEWD-D) While holding fl~at PULLEYin the LOOP, SECURELYassemble the PULLEYBtL4.CKETover the PULLEYas shown in (DETAILE) on drawing, using one (1) 318

2 IN. BOLT,two (2) 3,'8 IN. \VASI-I~RS,and one (I) 3~8 IN. LOCK

¯Route the LINK CABLEas shown on drawing. (ALSOSEE VIEWB-B)

oRun the LINKCABLEthrough the pre-deterrnined hole of ~he D-RINGas shown in ('.DETAILA) and attach one (I) D-RINGCABLECLIP around the ball end of the LINKCABLE.

Attach one (I) SHOCKCORDto the D-RINGCABLECLIP on the end of the LINK CABLEas shovrn in (DETAILA).

Route the SHOCKCORDup and around the: pro-determined 2 IN. PULLEYabove the D-RINGas shown in (VIEWC-C). and down~o the BASE.

Attach one (1) SWIVELto the end of the SHOCKCORD.Slip ti;e end of the SWIVELover the L-PIN on the BASE,and position the SWIVELdirectl: over the FIRSTPULLEYas shown in (VIEWB-B) drawing.

oO