JVC LVT1348-003A manual Introduction, Precautions, How to Read This Manual

Page 6

Introduction

Precautions

Installation

•Install in a place which is level, dry and neither too hot nor too cold—between 5°C and 35°C.

•Install the System in a location with adequate ventilation to prevent internal heat buildup inside the System.

DO NOT install the System in a location near heat sources, or in a place subject to direct sunlight, excessive dust or vibration.

•Leave sufficient distance between the System and the TV.

•Keep the speakers away from the TV to avoid interference with TV.

Power sources

•When unplugging the System from the wall outlet, always pull on the plug, not the AC power cord.

DO NOT handle the AC power cord with wet hands.

Moisture condensation

Moisture may condense on the lenses inside the System in the following cases:

•After starting to heat the room

•In a damp room

•If the System is brought directly from a cold to a warm place.

Should this occur, the System may malfunction. In this case, leave the System turned on for a few hours until the moisture evaporates, unplug the AC power cord, then plug it in again.

Internal heat

•A cooling fan is mounted on the rear panel to prevent heat buildup inside the main unit (see page G-1).

For safety, observe the following carefully:

•Make sure there is good ventilation around the main unit. Poor ventilation could

overheat and damage the System.

• DO NOT block the cooling fan and the ventilation openings or holes. If they are blocked by a newspaper or cloth, etc., the heat may not be able to get out.

Others

•Should any metallic object or liquid fall into the System, unplug the AC power cord and consult your dealer before operating any further.

DO NOT disassemble the System since there are no user serviceable parts inside.

•If you are not going to operate the System for an extended period of time, unplug the AC power cord from the wall outlet.

If anything goes wrong, unplug the AC power cord and consult your dealer.

How to Read This Manual

To make this manual as simple and easy-to-understand as possible, we have adapted the following methods:

•Button and control operations are explained as listed in the table below. In this manual, the operations using the remote control are mainly explained; however, you can use the buttons and controls on the main unit if they have the same (or similar) name and marks.

•Some related tips and notes are explained later in the sections “Learning More about This System” (on pages 40 to 42) and “Troubleshooting” (on page 43), but not in the same section explaining the operations. If you want to know more about the functions, or if you have a doubt about the functions, go to these sections and you will find the answers.

 

 

 

 

 

 

Indicates that you press the button

 

 

 

 

 

 

briefly.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Indicates that you press the button

 

 

 

 

 

 

 

 

 

 

 

briefly and repeatedly until an

 

 

 

 

 

 

option you want is selected.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Indicates that you press one of the

 

 

 

 

 

 

 

 

 

 

 

 

buttons.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Indicates that you press and hold the

 

 

 

2 sec.

 

 

button for a specified period.

 

 

 

 

 

• The number inside the arrow

 

 

 

 

 

 

 

 

 

 

 

 

indicates the period of press (in this

 

 

 

 

 

 

example, 2 seconds).

•If no number is inside the arrow, press and hold until the entire procedure is complete or until you get a result you want.

Indicates that you turn the control toward the specified direction(s).

 

 

 

 

 

Indicates that this operation is only

 

 

Remote

 

 

 

 

possible using the remote control.

 

 

ONLY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Indicates that this operation is only

 

 

 

 

 

 

 

Main Unit

 

 

possible using the buttons and controls on

 

 

ONLY

 

the main unit.

 

 

 

 

 

 

 

 

 

 

 

2

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Instructions If in Doubt Consult a Competent Electrician Page Above ALL Contents Precautions How to Read This ManualIntroduction Prepare the Remote Control Getting StartedUnpack Hook Up For better FM/AM reception Outdoor FM antenna not suppliedTo connect the speaker cords Selecting the Video SignalChanging the Scanning Mode To assemble and connect the AM loop antennaPlayable Disc Types If appears on the TV screen when you press aBefore Operating the System DVD Video-digital audio formatsDisplay Indicators W e r t y uIndications on the main display while operating a disc While playing back a disc While disc play is stoppedTo turn off the clock indication Daily Operations-PlaybackTo turn off standby the System For private listeningListening to the Radio To preset the stationsTo tune in to a preset station To select the band-FM or AM To tune in to a stationTo select a disc Playing Back a DiscTo insert a disc To select a chapter/trackFor SVCD/VCD with PBC To use 3D PhonicFor DVD Video/DVD Audio To locate a particular positionPlaylist Play List For DVD-VROriginal program Original Program Show the Original Program or Play ListTo connect other equipment How to install the USB driversPlaying Back from Other Equipment To select other equipment for the sourceTo adjust the tone-BASS/TREBLE Adjusting the VolumeAdjusting the Sound To emphasize the sound-SOUND TurboMaking DVD Voice Clear-CLEAR Voice Presetting Automatic DVD Sound IncreaseChanging the Display Brightness-DIMMER Level-DVD LevelTo select a preset picture tone To adjust the picture toneChanging the Picture Tone-VFP Video Turning Off the Power Automatically onlyTo turn off the System after playback is over- Auto Standby Receiving FM Stations with RDS Advanced Radio OperationsSearching for a Program by To show the RDS informationSwitching Temporarily to a Program Your Choice AutomaticallyUnique Disc Operations Selecting the Sound TrackWhile playing a DVD Video Selecting the Subtitle Language Playing Back a Bonus GroupFrame-by-frame playback To replay the previous scenesZoom only Slow-motion playbackBefore starting playback, activate Program Play Advanced Disc OperationsProgramming the Playing Order For SVCD/VCD/CDTo exit from Program Play To check the programmed contentsTo modify the program To exit from Random PlayPlaying Repeatedly Repeat PlayRepeat On-Screen Disc Operations On-screen Bar InformationOn-screen bars Changing the time information Time Search Chapter/Track Search Operations on the Control ScreenTo move the highlight bar between group list and track list To select a group/track in the list Unique Jpeg OperationsTo zoom in the still picture To start playbackTimer Operations Make the timer setting as you wantTo turn off the Timer after its setting is done How Daily Timer actually worksSetup Menu Operations Operating Procedure RemoteSetup Menu Icons Select one of the following 169 Picture Setup MenuLanguage Setup Menu LB Letter BoxAudio Setup Menu Select one of the followingTo play DivX files Others Setup Menu Dynamic Range CompressionDivX Registration DivX registration menu Operating the TV Operating TV RemoteTo operate the TV Additional Information Learning More about This SystemUnique Disc Operations see pages 22 to Daily Operations-Sound&Other AdjustmentsAdvanced Radio Operations see pages On-Screen Disc Operations see pages 28 toCleaning the System MaintenanceSetup Menu Operations see pages 35 to Handling discsTroubleshooting Language Code List Optical Digital OUT Signals OutputParts Index Specifications UX-GD7 Micro Component System

LVT1348-003A specifications

The JVC LVT1348-003A is a versatile and impressive accessory designed for use with various JVC audio and video equipment. Known for its reliability and innovative features, this accessory is an essential component for enhancing the performance and usability of compatible devices.

One of the main features of the JVC LVT1348-003A is its high-quality materials and construction. JVC has a reputation for producing durable products, and this accessory is no exception. The LVT1348-003A is designed to withstand everyday use while maintaining its functionality, making it an excellent choice for both casual and professional applications.

Another significant aspect of the LVT1348-003A is its compatibility with a wide range of JVC devices. This feature ensures that users can integrate the accessory seamlessly into their existing audio or video setups without the need for extensive modifications. Whether for home theater systems, video editing setups, or portable electronics, the LVT1348-003A provides flexibility and convenience.

In terms of technology, the LVT1348-003A incorporates advanced sound processing capabilities. This enables the accessory to deliver clear and precise audio, enhancing the overall listening experience. The use of cutting-edge engineering ensures that users can enjoy high-fidelity sound, making it ideal for music lovers and cinephiles alike.

The design of the LVT1348-003A is another aspect worth noting. It features a compact and lightweight design that is easy to transport and install. This portability is particularly useful for users who may need to set up their equipment in different locations, such as during live events or presentations.

Moreover, the LVT1348-003A includes various input and output options, providing users with the flexibility to connect multiple devices. This capability allows for greater customization and creativity in audio and video setups, meeting the diverse needs of various users.

Overall, the JVC LVT1348-003A stands out with its robust build, extensive compatibility, advanced technology, and thoughtful design. As a reliable accessory, it not only enhances the performance of JVC audio and video equipment but also enriches the user experience, making it an ideal choice for anyone looking to elevate their audio-visual endeavors.
Top Page Image Contents