JVC FS-V5 manual Using the Cassette Deck Recording, Standard Recording

English

■Using the Cassette Deck

■(Recording)

AUTO TAPE SELECTOR

AUTO PRESET

TAPE @ #

7

REMOTE CONTROL RM-RXFSV5
DIMMER	SLEEP	POWER
			REC	REC	REV.MODE	SLEEP CLOCK	REV. MODE
						TIMER/
DISPLAY	FM MODE	MD/AUX
				AHB PRO	VOLUME	SNOOZE
AHB PRO	AUTO	CD
	PRESET
PROGRAM RANDOM		REPEAT
BASS	TREBLE	CANCEL
	UP						Tape Direction indicator
	SET
	DOWN
TAPE	TUNER	CD						Reverse Mode
						TAPE REC indicator		indicator
	BAND

VOLUME	When the System is in use, the display shows other items as well.
	For simplicity, we show here only the items described in this section.

Recording onto a tape from any of the sound sources is simple. Just place a tape in the Cassette Deck, have the source ready, make one or two settings, and you’re ready to record. For each source the pro- cedure is a little bit different so we explain each separately. But first, here are a few things to make your recordings better.

Things To Know Before You Start Recording —————————————

■It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the con- sent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein.

■When you want to record onto both sides of a tape, you can set Reverse mode to do so. Recording automatically stops after re- cording in the 2 direction. Therefore, make sure that the tape di- rection is 3 when recording with Reverse mode on.

■The recording level, which is the volume at which the new tape is being made, is automatically set correctly, so it is not affected by the VOLUME control on the System. Nor is it affected by adjusting the sound effects. Thus, during recording you can ad- just the sound you are actually listening to without affecting the recording level.

■Two small tabs on the back of the cassette tape, one for side A and one for side B, can be removed to prevent accidental erasure or recording.

Type II detection slot

Adhesive tape

■To record on a cassette with the tabs removed, you must cover the holes with adhesive tape first. However, when a type II tape is used, only cover part of the hole as shown, since the other part of the hole (Type II detection slot) is used to detect the tape type.

■Type I and Type II tapes can be used for recording.

Note: At the start and end of cassette tapes, there is leader tape which cannot be recorded onto. Thus, when recording CDs or radio broadcasts, wind on the leader tape first to ensure getting the begin- ning of the recording.

CAUTION: If a recording you make has excessive noise or static, the Unit may have been too close to a TV which was on during the recording. Either turn off the TV or increase the distance between the TV and the System.

Standard Recording

You can record any sound source to tape as follows:

■1. Insert a blank or erasable tape into the

Cassette Deck and wind past the tape leader.

■2. Press the REV. MODE button on the Unit if you want to record on both sides of the tape.

Press the button until the indicator is lit.

•When using Reverse mode, insert the tape so that it will be recorded in the forwards 3 direction.

■3. Check the recording direction for the tape.

Make sure that the Tape Direction indicator is the same as that for the tape in the Cassette Deck. If the directions are different, press the TAPE @ # button to correct the tape direction and then press the e button to stop the tape.

■4. Prepare the source, by, for example, tuning in a radio station or turning on connected auxiliary equipment.

Note: For CD recording, refer to “CD Direct Recording” men- tioned below.

■5. Press the REC button on the Unit.

The “TAPE REC” indicator lights up and the System begins re- cording.

•If the tab of the cassette tape is removed to prevent erasure or recording, “NO REC” will appear on the display.

13