Vision Fitness X6850HRT manual E P 1 Orange BAG, E P 4 Green BAG

S T E P 1 ORANGE BAG

•Place a piece of packaging under the front of the unit to aid in assembly of the front foot.

•Secure the front stabilizer tube to the base frame plate with four socket head bolts (M8x20L) and four arc washers (8.2x18x1.5T). Tighten with the 6mm L-shaped wrench.

S T E P 2 BLUE BAG

• Take the right pedal arm and set the

roller wheel in the aluminum guide track.

Slide the opposite end of the pedal arm

into the U-shaped knuckle bracket.

Slide a socket head bolt (M10x55L)

with a washer (10x24.5x1T) through

the hole in the knuckle bracket and

pedal arm. Fix in place with a

washer (10x24.5x1T) and nylon nut

(M10). Tighten with the 8mm L-shaped

Knuckle Bracket

S T E P 2

S T E P 4 GREEN BAG

• Remove protective covers from sleeves of the pedal arms.

IMPORTANT: The washers in the following step must be assembled in the correct order.

• Slide one thin metal wave washer

S T E P 1(26x36x0.3T), one flat washer (25.5x38x1T), and one plastic wave washer (26x36x2T) onto the axle of the right link arm. Slide the axle of the right link arm through the sleeve on the right pedal arm. Secure the link arm onto the pedal arm with the plastic wave washer (26x36x2T), end cap, and bolt (M8x12L). Tighten with the 5mm L-shaped wrench.

		• Repeat the step on the left side.
Front Stabilizer Tube	S T E P 5	BLACK BAG

wrench and the 17mm wrench.

• Slide the pedal arm cover over the

knuckle joint and fix in place with a bolt

(M5x12L). Tighten with the screwdriver.

• Repeat these steps on the left side.

S T E P 3 PINK BAG

• Slide the console mast boot onto

the console mast.

• Cut the zip ties holding the cables

and wires onto the console mast.

• Attach the mounting plate to the

bottom of the console mast with four

socket head bolts (M10x25L) and four

lock washers (M10). Tighten as much as

possible with the 8mm L-shaped wrench.

• Mount the console mast on the

frame by sliding the guide hole on the

mast mounting plate over the guide

screw on the front of the frame bracket.

Place a lock washer (M8) followed by

a flat washer (8x16x2T) on each of

the four remaining socket head bolts

(M8x25L). Insert the bolts to the rear

holes but do not completely tighten.

Next, insert the bolts to the front holes.

Tighten all four bolts as much as possible

with the 6mm L-shaped wrench.

• Wrap the wire tie that exits the hole

at the bottom front side of the console

mast around the data cable, coaxial

cable, and TV power cable coming

up from the frame. Pull the wire tie

and all cables up through the top of

TV Bracket

Cables

Heart Rate

Wires

Data Cable

Console Plate
	Console Mast
	Console Mast
	Boot
S T E P 3	Frame Bracket
Mounting Plate

Console

S T E P 6

Accessor y Tray

Rotation

Housing

NOTE: With this next step it is helpful to have a second person to hold the dual-action arms in place while you assemble them.

•Take the right dual-action arm and center the holes in the rotation housing on the console mast. Secure with four socket head bolts (M8x25L) and four lock washers (M8). Tighten with the 6mm T-shaped wrench.

•Attach the dual-action arm rotation cover to the dual-action arm center. Secure in place with two bolts (M5x15L). Tighten with the screwdriver.

•Slide a spacer onto each side of the socket joint located on the end of the link arm. Slide the bottom of the dual- action arm bracket over the link arm socket and spacers. From the outside of the bracket, slide the bolt (M8x55L) through the hole in the bracket and socket joint. Secure with a washer (8x16x1T) and nylon nut (M8). Tighten with the 6mm T-shaped wrench and 13mm wrench.

•Attach the inside dual-action arm cover onto the bottom of the dual- action arm with a bolt (M5x15L). Insert the plastic connector to the inside dual-action arm cover. Slide the outside dual-action arm cover onto the other end of the plastic connector. Secure the outside dual-action arm cover to the bottom of the dual-action arm with a bolt (M5x15L). Tighten both bolts with the screwdriver.

•Repeat these steps on the left side.

the console mast.

• Remove the protective plastic

around the cables and data cable.

• Tuck the coaxial and TV power

cables into the console mast.

NOTE: If you have purchased the TV bracket assembly, remove the screws from the TV bracket cover located at the front of the console mast, and remove the cover. Feed the coaxial and TV power cables through the hole at the front of the console mast.

•Insert a zip tie through the hole in the middle of the console plate and loop it around the heart rate wires and data cable. Pull to snug, but do not over tighten.

	End Cap	Plastic Wave
		Washer
		Plastic Wave
		Washer
		Flat Washer
Pedal Arm		Thin Metal
		Wave Washer
S T E P 4	Link Arm

S T E P 6

Dual - Action

Arm

S T E P 5

YELLOW BAG

•Slide the accessory tray onto the console mast. Secure in place with four panhead bolts (M8x20L). Tighten with the 5mm L-shaped wrench.

•Remove the four bolts (M5x12L) from the back side of the console. Connect the data cable and the heart rate wires to the plugs in the back side of the console. Place the console on the mast and secure in place with the bolts (M5x12L).

•Place the X6850HRT in its intended location and plug in the power cord to the electrical outlet.