JVC CA-MXGA8V, CA-MXGA9V manual Common Operations, Turning On or Off the Power, Setting the Clock

Page 14

English

Common Operations

Turning On or Off the Power

To turn on the unit, press

STANDBY/ON so that the STANDBY lamp goes off.

To turn off the unit (on standby), press

STANDBY/ON again so that the

STANDBY lamp lights up.

A little power is always consumed even while the unit is on standby.

To switch off the power supply completely, unplug the AC

power cord from the AC outlet.

When you unplug the AC power cord or if a power failure occurs

The clock is reset to “0:00” right away, while the tuner preset stations (see page 13) will be erased in a few days.

To check the clock time

Press and hold SET/DISPLAY while playing any source.

Each time you press and hold the button, the source indication and the clock time alternate on the display.

To adjust the clock again

If you have adjusted the clock before, you need to press CLOCK/TIMER repeatedly until the clock setting mode is selected.

Each time you press the button, the clock/timer setting modes change as follows:

DAILY ON TIME REC

Cancelled Clock ON TIME setting

(The hour digits start flashing.)

When you unplug the AC power cord or if a power failure occurs

The clock loses the setting and is reset to “0:00.” You need to set the clock again.

Setting the AM Tuner Interval Spacing

Some countries space AM stations 9 kHz apart, and some countries use 10 kHz spacing.

Setting the Clock

Before operating the unit any further, first set the built in clock. You can set the clock whether the unit is on or off.

On the unit ONLY:

1 Press CLOCK/TIMER.

The hour digits start flashing on the display.

2 Turn 4/¢ to adjust the hour, then press SET/

DISPLAY.

The minute digits start flashing on the display.

• If you want to correct the hour after pressing SET/DISPLAY, press CANCEL/DEMO.

The hour digits start flashing again.

3 Turn 4/¢ to adjust the minute, then press SET/DISPLAY.

On the unit ONLY:

You can only change the AM tuner interval spacing while tuning into an AM station. (See page 13.)

Press STANDBY/ON

 

while holding down 7.

 

• Each time you press these buttons, the AM tuner interval spacing alternates between

9 kHz and 10 kHz.

Selecting the Sources

To listen to the FM/AM broadcasts, press FM/AM.

(See page 13.)

To playback CDs, press CD 3¥8 SELECT. (See pages 14 – 17.)

To playback tapes, press TAPE 2 3. (See page 23.)

To select the external equipment as the source, press AUX.

When you press the play button for a particular source (FM/AM, CD 3/8 SELECT, TAPE 2 3 and AUX), the unit turns on (and the unit starts playing the source if it is ready —

COMPU PLAY CONTROL).

About the audio level indicator

All the audio level indicators light up when no signals come in.

– 10 –

Image 14
Contents Instructions Page English Class Laser Product About This Manual PrecautionsIntroduction Contents Location of the Buttons and Controls Remote ControlRemote Control Front Panel Become familiar with the buttons and controls on your unitSee pages in the parentheses for details Front PanelDisplay Window 14 15, 17Getting Started Supplied AccessoriesConnecting Antennas FM antennaClose the speaker terminals Connecting SpeakersTurn the AM loop antenna until you have the best reception AM antennaFor CA-MXG780V/G750V/GA7V Surround SpeakersTo connect surround speakers Cancelling the Display Demonstration Connecting Other EquipmentAdjusting the Voltage Selector On the unit onlySetting the Clock Turning On or Off the PowerSetting the AM Tuner Interval Spacing Common OperationsSelecting the Sound Modes Adjusting the VolumeTo turn down the volume level temporarily Reinforcing the Bass SoundTo use your own sound mode Creating Your Own Sound Mode Manual ModeOn the unit only Select one of the preset sound modes SEA Sound Effect Amplifier modesTuning in a Preset Station Tuning in a StationPresetting Stations Listening to FM and AM BroadcastsPress the same 0 you have pressed in step Playing Back CDs CD/CD-R/CD-RWLoading CDs Repeat steps 1 to 3 to place other CDsPlaying Back the Entire Discs Continuous Play Basic CD OperationsPress CD 3¥8 Select Program PlayLoad CDs Program other tracks you want Press Program so that Program appears on the displayProhibiting Disc Ejection Tray Lock Random indicator also lights up on the displayTo cancel the prohibition and unlock Load CDsPlaying a Video CD Playing Back Video CDsSelecting Video Output PAL, MULTI, Ntsc Loading DiscsPlaying Video CDs with PBC Function Menu Play Basic Concept of the PBC functionSpecial Plays for a Video CD Resuming PlayPlaying a Multiplex Sound CD To stop and cancel the video intro playTo stop and cancel the highlight play Viewing the Highlights of a Video CDMP3 Disc Playback Programming tracksLocating the Beginning of a Song Music Scan Playing Back TapesPlaying Back a Tape Press Eject 0 for deck B RecordingRecording a Tape on Deck B Start recording On the unit only Press REC START/STOPCD Direct Recording To record on both sides Reverse ModeDubbing Tapes On the unit only Press Tape 2 3, thenPress Edit Auto Edit RecordingOn the unit only Load CDs To change the tape length manuallySinging Along with Multiplex Karaoke Discs MPX Using the MicrophonesSinging along Karaoke Connect the microphones Press CD 3/8 SELECT, then Adjust the Music Key Control for CD play onlyRecording Your Singing Microphone mixingUsing the Timers Using Daily TimerTurn 4 / ¢ to set the volume level When selecting Tuner FM or Tuner AMWhen selecting CD Press SET/DISPLAY to complete the Daily Timer settingHow Recording Timer works Using Recording TimerSelect the preset station On the remote control only Press Sleep Using Sleep TimerTimer Priority Wait for about 5 seconds after specifying the time lengthTo clean the disc MaintenanceCleaning the unit Handling discsTroubleshooting SymptomSpecifications Important for mains AC line