PART | R0201A |
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.
Key |
|
| Key |
|
| Key |
|
|
No. | Qty. | Description | No. | Qty. | Description | No. | Qty. | Description |
1 | 2 | Foot Rail Insert | 47 | 4 | Isolator | 93 | 2 | Lift Pivot Bolt |
2 | 2 | Foot Rail | 48 | 4 | Isolator Screw | 94 | 2 | Wheel Bolt |
3 | 2 | Foot Rail Cap Screw | 49 | 16 | Fastener | 95 | 2 | Wheel |
4 | 1 | Left Fait Rail Cap | 50 | 1 | Belly Pan | 96 | 1 | Right Endcap Insert |
5 | 2 | Frame Pivot Bolt | 51 | 1 | Right Foot Rail Cap | 97 | 1 | Grommet |
6 | 2 | Frame Pivot Spacer | 52 | 1 | Walking Platform | 98 | 1 | Upright Wire Harness |
7 | 1 | Magnet | 53 | 6 | Platform Screw | 99 | 4 | Base Pad |
8 | 1 | Front Roller/Pulley | 54 | 4 | Rear Platform Screw | 100 | 6 | 3/4” Screw |
9 | 8 | Frame Pivot Nut | 55 | 2 | Rear Isolator | 101 | 1 | Motor Washer |
10 | 1 | Reed Switch/Sensor | 56 | 5 | Ground Screw/ | 102 | 2 | Extension Leg |
|
| Wire |
|
| Controller Screw | 103 | 2 | Extension Cap |
11* | 1 | Latch Assembly | 57 | 1 | Ground Wire | 104 | 2 | Incline Warning Decal |
12 | 1 | Reed Switch Clip | 58 | 1 | Rear Endcap | 105 | 1 | Shock |
13 | 1 | Lift Frame | 59 | 2 | Rear Roller Adj. Bolt | 106* | 2 | Extension Leg |
14 | 3 | Star Washer | 60 | 1 | Warning Decal |
|
| Assembly |
15* | 1 | Motor Assembly | 61 | 1 | Allen Wrench | 107 | 1 | Chest Pulse Wire |
16 | 1 | Motor | 62 | 1 | Rear Roller | 108 | 1 | Book Holder |
17 | 1 | Pulley/Flywheel/Fan | 63** | 1 | Optional Chest Pulse | 109 | 1 | Power Cord Grommet |
18 | 1 | Motor Belt |
|
| Strap | 110 | 1 | Frame |
19 | 1 | Motor Pivot Nut | 64** | 1 | Optional Chest Pulse | 111 | 2 | Catch Screw |
20 | 1 | Motor Tension Nut | 65 | 1 | Left Foam Grip | 112 | 1 | Catch |
21 | 1 | Motor Tension Bolt | 66 | 2 | Handrail Extension | 113 | 1 | Audio Wire |
22 | 1 | Motor Pivot Bolt | 67 | 8 | 1/2” Screw | 114 | 1 | Walking Belt |
23 | 1 | Hood | 68 | 1 | Lock Knob | 115 | 1 | 15” Wire Harness |
24 | 2 | Incline Motor Bolt | 69 | 1 | Upright | 116 | 1 | 20” Wire Harness |
25 | 4 | Plastic | 70 | 1 | Lock Knob Sleeve | 117** | 2 | Hand Weight |
26 | 1 | Power Board | 71 | 1 | Spring | 118 | 2 | Endcap Spacer |
27 | 5 | Screw | 72 | 1 | Lock Pin Collar | 119 | 2 | Thick Base Pad |
28 | 1 | Choke | 73 | 1 | Pin Clip | 120** | 1 | IFIT.com Module |
29 | 1 | Controller | 74 | 1 | Lock Pin | 121** | 1 | IFIT.com Videocassette |
30 | 1 | Electronics Plate | 75 | 1 | Right Foam Grip | 122** | 1 | IFIT.com CD |
31 | 1 | 8” Wire Harness | 76 | 1 | Pulse Bar | # | 1 | 12” White Wire, M/F |
32 | 1 | Front Roller Adj. Bolt | 77 | 2 | Pulse Bar Washer | # | 1 | 8” White Wire, 2F |
33 | 6 | 1 1/4” Screw | 78 | 2 | Pulse Bar Bolt | # | 1 | 14” Blue Wire, 2F |
34 | 3 | Roller Washer | 79 | 2 | Upright Endcap | # | 1 | 4” Blue Wire, 2F |
35 | 1 | Front Roller Nut | 80 | 4 | Belly Pan Screw | # | 1 | 4” Black Wire, 2F |
36 | 1 | Incline Motor | 81 | 1 | Console Base | # | 1 | 12” Green Wire, 2/Ring |
37 | 1 | Incline Motor Stop | 82 | 1 | Console | # | 1 | 8” Green Wire, F/Ring |
38 | 1 | Belly Pan | 83 | 16 | Console Screw | # | 1 | User's Manual |
39 | 2 | Belly Pan Screw | 84 | 1 | Key/Clip |
|
|
|
|
| (Long) | 85 | 1 | IFIT.com Wire | * Includes all parts shown in box | ||
40 | 2 | Static Decal | 86 | 1 | Jack | **For information about the optional | ||
41 | 1 | Circuit Breaker | 87 | 10 | Console Back Screw | chest pulse sensor and hand | ||
42 | 1 | Power Cord | 88 | 1 | Console Back | weights, see page 18 | ||
43 | 1 | On/Off Switch | 89 | 1 | Releaseable Tie | # These parts are not illustrated | ||
44 | 1 | Left Endcap Insert | 90 | 1 | Cable Tie Screw |
|
|
|
45 | 4 | Belt Guide Screw | 91 | 1 | Cable Tie Clamp |
|
|
|
46 | 1 | Belt Guide | 92 | 1 | 8” Cable Tie |
|
|
|