ProForm PFTL52580 user manual Assembly, Handrail Bolt yet

Page 5

ASSEMBLY

Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not

 

dispose of the packing materials until assembly is completed. Refer to the drawings below to identify the small

 

parts used in assembly. Assembly requires the included allen wrench

and your own phillips screw-

 

driver

, adjustable wrench

, open end wrench

and scissors

.

1/2" Screw (13)Ð2

Handrail Washer (16)Ð2

Extension Leg Screw (34)Ð2

 

 

 

Flange Nut (57)Ð2

Handrail Bolt (15)Ð2

3/4" Screw (59)Ð4

 

 

 

3 1/2" Handrail Bolt (89)Ð2

 

3/8" Washer (61)Ð2

 

 

1.With the help of a second person, carefully lay the treadmill on its right side as shown (refer to the drawing on page 4 to identify the right side).

Insert the Extension Legs (41) into the treadmill. Make sure that the Extension Legs are turned so the Base Pads (36) are on the indicated side. Attach each Extension Leg with an Extension Leg Screw (34).

With the help of a second person, carefully raise the treadmill to the upright position so the Extension Legs (41) are resting flat on the floor.

Refer to the inset drawing. Remove the nut, bolt, and shipping bracket from the left Upright (14).

2.Refer to HOW TO LOWER THE TREADMILL FOR USE on page 11. Follow the instructions in step 2 to lower the treadmill.

Cut the plastic ties that hold the cage nuts in each Handrail (2, 32)

Position the Left Handrail (2) on the left Upright (14). The lower end of the Left Handrail should be on the outside of the Extension Leg (41) as shown. (Note: The Right Handrail will have a ÒRightÓ sticker placed on it.) Thread a Handrail Bolt (15) with a Handrail Washer (16) into the left Upright and the Left Handrail. Do not tighten the

Handrail Bolt yet.

Attach the lower end of the Left Handrail (2) to the Extension Leg (41) with a 3 1/2Ó Handrail Bolt (89), a 3/8Ó Washer (61), and a Flange Nut (57). Do not tighten the

Handrail Bolt yet.

1

34

 

41

 

 

36

 

 

 

Shipping

Bolt

 

Bracket

 

41

Nut

 

 

 

36

34

14

 

 

 

2

Plastic Tie

 

15

 

 

16

 

 

2

 

 

14

 

 

41

57

 

 

 

89 61

 

5

Image 5
Contents Customer HOT Line QUESTIONS?Model No. PFTL52580 Serial No Important Precautions Table of ContentsPage Left Side Right Side Before YOU BeginHandrail Bolt yet AssemblyTighten all parts used in this step and in steps 2 Make sure that the Wire Harness is not pinchedPerformant Lubetm Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Battery Installation Diagram of the ConsoleInsert the key fully into the power switch Step by Step Console OperationMeasure your pulse, if desired Reset the console and start the walking beltAdjust the incline of the treadmill as desired HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Top Maintenance and TROUBLE-SHOOTINGProblem The power turns off during use Problem The walking belt slips when walked on Problem The walking belt slows when walked onProblem The walking belt is off-center when walked on Workout Guidelines Conditioning GuidelinesExercise Intensity Suggested Stretches Key No. Qty Description Part LISTÑModel No. PFTL52580Exploded DRAWINGÑModel No. PFTL52580 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty