ProForm PFTL43205.1 user manual Ground Wire

Page 7

2.Attach a Wheel (66) to the base of the Uprights (69) with a Wheel Bolt (64) and a Wheel Nut (32) as shown. Do not overtighten the Wheel Bolt; the Wheel should turn freely.

With the help of a second person, carefully tip the tread- mill onto its other side. See assembly step 1 and attach the other Extension Leg (63) and Base Pads (57). Next, attach the other Wheel (66) as described above.

With the help of a second person, carefully tip the tread- mill so the base of the Uprights (69) is flat on the floor.

3.Remove the two bolts (A) attaching the Weight Rack (102) to the Uprights (69), and discard the bolts. Remove the Weights from the Weight Rack. The Weight Rack will be assembled in step 6.

Remove the tie from the Wire Harness (42). Hold one of the Handrails (71) near the right Upright (69), and insert the Wire Harness into the opening in the bottom of the Handrail and out of the indicated hole in the top.

Set the Handrail (71) on the right Upright (69), and tighten two Extension Leg Bolts (93) with two Handrail Star Washers (95) into the Handrail and the right Upright. Make sure that the Wire Harness (42) is not pinched.

Attach the other Handrail (71) to the left Upright (69) as described above. Note: There is not a wire harness on the left side.

4.Have another person hold the Console Base (47) near the right Handrail (71). If there is a green ground wire extending from the Console Base, attach the end of the ground wire to the indicated small hole in the right Handrail with the Silver Ground Screw (75).

Connect the Wire Harness (42) to the wire harness on the Console Base (47). Make sure to connect the con- nectors properly (see the inset drawing). The con- nectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn one connector and try again. IF THE

CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.

2

64

 

 

 

 

69

66

 

 

 

32

 

3

 

 

93

 

 

71

 

 

95

42

 

69

 

 

93

 

A

95

 

71

 

69

 

A

 

102

 

 

4

 

 

47

 

 

75

Ground

 

 

 

 

Wire

 

42

 

 

71

 

 

 

42

 

7

Image 7
Contents Model No. PFTL43205.1 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Page Right Side Before YOU BeginBack Assembly 102 Ground Wire Page HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to Turn on the Power HOW to USE the Manual Mode Turn on the fan if desired Measure your heart rate if desiredWhenkey. you are finished exercising, remove Whenkey. the program is completed, remove HOW to USE a Trainer ProgramSelect a trainer program Follow your progress with the displaysSelect a custom program HOW to Create a Custom ProgramHOW to USE a Custom Program HOW to USE the Hand Weights Information MODE/DEMO ModeHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked on Exercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Page Key Qty Description Part LIST-Model No. PFTL43205.1R0806A Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT