ProForm PFTL51105.1 user manual Knob Spring Large Hole Collar Pin

Page 7

2.With the help of a second person, carefully raise the Uprights (84) to a vertical position.

Have the second person hold the console assembly near the Uprights (84) as shown. Look under the console as- sembly and locate the Console Wire Harness (78).

Cut the plastic ties securing the Upright Wire Harness (77) to the right Upright (84). Next, connect the Upright Wire Harness to the Console Wire Harness (78). Make sure to connect the connectors properly (see the inset drawing). The connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn one con- nector and then try again. IF THE CONNECTORS ARE

NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.

3.Insert the Wire Harnesses (77, 78) down into the right Upright (84).

Set the console assembly on the Uprights (84). Be care- ful to avoid pinching the Wire Harnesses (77, 78). While a second person holds the console assembly, at- tach it with four Console Bolts (64) and four Star Washers

(8) as shown; start all four Console Bolts and then firmly tighten them.

4.Attach the Latch Housing (73) to the left Upright (84) with two Latch Screws (50); start both Latch Screws and then tighten them. Note: Make sure that the large hole in the Housing is on the indicated side.

Remove the knob from the pin. Make sure that the collar and the spring are on the pin. (Note: If there are two col- lars, place one on each side of the spring.) Next, insert the pin into the Latch Housing (73). Then, tighten the knob back onto the pin.

2

 

 

 

Console

 

 

Assembly

 

 

 

78

 

 

77

 

78

 

 

 

84

 

77

 

3

Console

 

 

Assembly

 

 

77, 78

 

 

8

 

 

64

8

 

 

 

84

64

 

84

 

 

4

 

 

 

 

84

 

73

 

Knob

Spring

50

Large Hole

Collar

Pin

5.Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread- mill. Note: Extra hardware may be included. Keep the included allen wrench in a secure place; the large allen wrench is used to adjust the walking belt (see page 20).

7

Image 7
Contents Model No. PFTL51105.1 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Page Right Side Before YOU BeginBack Make sure that the power cord is unplugged AssemblyFold the treadmill until it is completely assembled Knob Spring Large Hole Collar Pin Wire HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerTurn on the fan if desired Measure your heart rate if desiredWhenkey. you are finished exercising, remove Select a preset program HOW to USE a Preset ProgramSelect a heart rate program HOW to USE a Heart Rate ProgramFollow your progress with the display Optional Chest Pulse Sensor Information MODE/DEMO ModeHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Top Exercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Qty Description R0605AExploded DRAWING-Model No. PFTL51105.1 Exploded DRAWING-Model No. PFTL51105.1 Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT