ProForm PFTL63105.0 user manual Problem The walking belt slows when walked on Top

Page 20

With the help of a second person, carefully raise the Uprights (84) to the position shown. Carefully pivot the Hood (41) off.

Locate the Reed Switch (63) and the Magnet (46) on the left side of the Pulley (47). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8”. If necessary, loosen the Screw (3), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood, and run the treadmill for a few minutes to check for a correct speed reading.

PROBLEM: The walking belt slows when walked on

41

84

 

Top

 

View

 

1/8”

 

46

3

63

47

 

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 9.

b. If the walking belt is overtightened, treadmill perfor- mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn both rear roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 inches off the walking platform. Be careful to keep the walk- ing belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

b

2”–3”

Rear Roller Bolts

c. If the walking belt still slows when walked on, see the front cover of this manual.

PROBLEM: The walking belt is off-center or slips when walked on

SOLUTION: a. If the walking belt is off-center, first remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the allen wrench to turn the left rear roller bolt clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left bolt counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered.

b. If the walking belt slips when walked on, first re- move the key and UNPLUG THE POWER CORD. Using the allen wrench, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is cor- rectly tightened, you should be able to lift each edge of the walking belt 2 to 3 inches off the walking plat- form. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and care- fully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

a

b

20

Image 20
Contents Call TOLL-FREE QUESTIONS?Model No. PFTL63105.0 Serial No Table of Contents Important Precautions Page Back Before YOU BeginRight Side Fold the treadmill until it is completely assembled AssemblyMake sure that the power cord is unplugged Latch Screws and then tighten them Page PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeWhenkey. you are finished exercising, remove Measure your heart rate if desiredTurn on the fan if desired HOW to USE a Preset Program Select a preset programHOW to USE a Heart Rate Program Select a heart rate programFollow your progress with the display Information MODE/DEMO Mode Optional Chest Pulse SensorHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Top Conditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches R0805A Qty DescriptionExploded DRAWING-Model No. PFTL63105.0 Exploded DRAWING-Model No. PFTL63105.0 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty