ProForm PFTL59210 user manual Follow your progress with the displays

Page 13
Current Segment

The program display will show the first speed settings for the pro- gram. The Time/ Incline/Segment Time display will show how long the program will last.

3 Press the Start button or the Speed button to start the program.

A moment after the button is pressed, the tread- mill will automatically adjust to the first speed and incline settings for the program. Hold the handrails and begin walking.

Each program is divided into several time seg- ments of different lengths. The Time/Incline/ Segment Time display shows both the time re- maining in the program and the time remaining in the current segment. One speed setting and one incline setting are pro-

grammed for each seg- ment. The speed set-

ting for the first seg- ment will be shown in the flashing Current

Segment column of the program display. (The

incline settings are not

shown in the program display.) The speed set- tings for the next four segments will be shown in the four columns to the right.

When only three seconds remain in the first seg- ment of the program, both the Current Segment column and the column to the right will flash and a tone will sound. In addition, if the speed and/or incline of the treadmill is about to change, the Speed/Min-mile display and/or the Time/Incline/ Segment Time display will flash to alert you, and three tones will sound. When the first segment is completed, all speed settings will move one col- umn to the left. The speed setting for the second segment will then be shown in the flashing Current Segment column and the treadmill will au- tomatically adjust to the speed and incline settings for the second segment.

The program will continue in this way until the speed setting for the last segment is shown in the Current Segment column and no time remains in the Time/Incline/Segment Time display. The walk- ing belt will then slow to a stop.

Note: Each time a segment ends and the speed settings move one column to the left, if all of the indicators in the Current Segment column are lit, the speed settings will move downward so that only the highest indicators in the columns will appear in the program display. When the speed settings move to the left again and not all of the indicators in the Current Segment column are lit, the speed settings will move back up.

If the speed or incline setting for the current segment is too high or too low, you can manually override the setting by pressing the Speed or Incline buttons on the console. Every few times one of the Speed buttons is pressed, an additional indicator will light or darken in the Current Segment column. If any of the columns to the right of the Current Segment column have the same number of lit indicators as the Current Segment column, an additional indicator may light or darken in those columns as well. Important: When the current segment of the program ends, the treadmill will automatically adjust to the speed and incline settings for the next segment.

To stop the program temporarily, press the Stop button. The Time/Incline/Segment Time display will begin to flash. To restart the program, press the Start button or the Speed button. To end the program, press the Stop button, remove the key, and then reinsert the key.

4 Follow your progress with the displays.

Refer to step 5 on page 11.

5 Measure your heart rate, if desired.

See step 6 on page 12.

6 When the program is completed, remove the key from the console.

When the program has ended, make sure that the incline of the treadmill is at the lowest set- ting. Next, remove the key from the console and put it in a safe place.Note: If the displays and various indicators on the console remain lit after the key is removed, the console is in the “demo” mode. Refer to page 19 and turn off the demo mode.

When you are finished using the treadmill, move the on/off switch near the power cord to the off position and unplug the power cord.

13

Image 13
Contents Model No. PFTL59210 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Page Left Side Before YOU BeginRight Side Driver and rubber mallet AssemblyExtension Legs 103 remain in the Uprights Page Page HOW to Plug in the Power Cord Operation and AdjustmentPerformant Lubetm Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerHOW to USE Personal Trainer Programs When you are finished, remove the keyDistance/Laps Measure your heart rate, if desiredFollow your progress with the displays HOW to Connect Your Portable Stereo HOW to Connect Your Computer HOW to Connect Your Home StereoAudio Adapter Cable HOW to Connect Your VCRInsert the key into the console PressVCR. the Play button on your CD player orWhenkey. the program is completed, remove When the program has ended, remove the key HOW to USE Programs Directly from OUR WEB SiteFollow the on-line instructions to start the program Optional Hand Weights Information MODE/DEMO ModeHeart Rate display is blank Optional Chest Pulse SensorHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TROUBLE-SHOOTINGTop Problem The walking belt slows when walked on Exercise Intensity Conditioning GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Page Key Qty Description R0801ASave the Exploded Drawing for Future Reference Exploded Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT