ProForm 831.295062 user manual Troubleshooting, Problem The power turns off during use

Page 22

TROUBLESHOOTING

Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call toll-free 1-800-4-MY-HOME®(1-800-469-4663).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor that meets all of the specifications described on page 8. Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

PROBLEM: The power turns off during use

c

Tripped

Reset

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key fully into the console.

d.If the treadmill still will not run, please call toll-free 1-800-4-MY-HOME®(1-800-469-4663).

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. With the help of a second person, carefully tip the Upright Base (97) down as shown. Remove the five Hood Screws (44). Note: A phillips screwdriver with at least a 5” shaft is required.

a

44

 

 

44

 

97

 

44

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Assembly Operation Maintenance Part List and Drawing Model No Serial NoTable of Contents Important PrecautionsPage Right Side Before YOU BeginBack Assembly Make sure that the power cord is unpluggedUpright Base 107 Wire 116 Cylinder 108 HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeAvoid mov Measure your heart rate if desiredOn the foot Rails Turn on the fan if desiredHOW to USE a Preset Program Select one of the preset programsHOW to USE a Heart Rate Program Select a heart rate programEnter a maximum speed setting Enter your ageHOW to Connect Your Portable Stereo HOW to Connect Your MP3 Player or CD PlayerAudio Cable HOW to Connect Your Home Stereo HOW to Connect Your ComputerHOW to Connect Your VCR Press the Play button on your MP3 player, CD Player, or VCRMeasure your heart rate if desired Follow the on-line instructions to start Program Directly from OUR WEB SiteReturn to the treadmill and stand on the foot HOW to Level the Treadmill Information MODE/DEMO ModeOptional Chest Pulse Sensor HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useProblem The walking belt slows when walked on TopWorkout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R0105A Qty DescriptionIf a part is missing, call toll-free Exploded DRAWING-Model No 112 Full 90 DAY Warranty Sears, Roebuck and Co., Dept WA, Hoffman Estates, IL
Top Page Image Contents