ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own phillips screwdriver 
, adjustable wrench 
and scissors 
.
1.With the help of a second person, carefully raise the treadmill to the upright position. While the other person tips the treadmill to one side and holds it, insert one of the Extension Legs (103) into the treadmill. Make sure that the Extension Leg is turned so the Warning Decal
(20)is on top. Tighten two of the four Short Screws
(101)into the treadmill and the Extension Leg.
Next, tip the treadmill to the other side and attach the other Extension Leg (not shown) in the same way. Lower the side of the treadmill so that both Extension Legs
(103)are resting flat on the floor.
2.Refer to HOW TO LOWER THE TREADMILL FOR USE on page 11. Follow step 2 to lower the treadmill.
Next, attach the latch support to the center hole in the left Upright (82) with a 3/4Ó Screw (81). Make sure that the
Screw is tight, but do not overtighten it; if the Screw is overtightened, the latch will not slide smoothly.
Remove the tape from the Latch Assembly (77). Be care- ful to hold the parts together. Inset drawings A and B shows how the parts fits together. Make sure that the tabs on the latch are touching one side of the bracket and the back end of the latch is flush with the other side of the bracket. Then, insert the two springs into the bracket.
Attach the Latch Assembly (77) to the left Upright (82) with two 3/4Ó Screws (81).
3.Cut the plastic tie off the bracket on the base of each Upright (82). Next, cut the plastic tie off the Left Handrail
(74).Position the Left Handrail on the left Upright (82). The bracket on the base of the left Upright should be in- side of the lower end of the Left Handrail, as shown in inset drawing C.
Refer to inset drawing A. While a second person holds the Right Handrail (85) and the Console (not shown) near the right Upright (82), cut the indicated plastic ties off the Right Handrail. Do not cut the other plastic tie in the Right Handrail. Next, cut the plastic tie off the Upright Wire Harness (34) in the right Upright (82). Do not drop the Upright Wire Harness into the right Upright.
Refer to inset drawing B. Connect the Console Wire Harness
(48)to the Upright Wire Harness (34). The latch on the Console Wire Harness should snap onto the Upright Wire Harness. If the Wire Harnesses do not fit together easily, turn them; do not force the Wire Harnesses together.
1 |
|
|
|
20 |
|
|
|
103 |
|
|
|
101 |
|
|
|
2 | A |
|
|
82 |
| Bracket |
|
81 |
|
|
|
77 |
|
|
|
81 | Latch |
| |
|
| ||
Latch | B |
| Tabs |
Spring |
| ||
Support |
| ||
Flush |
| ||
|
| ||
| Spring |
| |
3 | Do not | A | 48 |
|
| 85 | |
| cut |
|
|
74 |
| Plastic |
|
| Ties |
| |
Plastic Tie |
| 82 | 34 |
|
| B |
|
|
| 48 |
|
|
| 34 |
|
| Plastic | C |
|
82 | Tie | 74 |
|
|
| ||
|
| Bracket |
|
5